I JUST ACQUIRED A 64 DEVILLE TURBO HYDRAMATIC TRANSMISSION FROM A PARTS CAR.

COMES WITH SPACER,FLYWHEEL AND TORQUE CONVERTER AND SHIELD. I DONT KNOW WHAT A FAIR

PRICE WOULD BE TO ASK. ANY SUGGESTIONS?

Views: 127

Reply to This

Replies to This Discussion

Stephen, with CAPS LOCK.

Jason is posting transmissions in his selling thread. Should give you an idea what he is charging. My guess is that he is a bit cheaper than the back street seller. The good thing with buying from Jason is that you get what you pay for and if any problems you will get 100% assistance. Check what it would cost having the transmission sent from Jason, using engineshipping or similar service. If you get a reliable and trustworthy transmission locally for less then go for it.

Most of these transmissions for sale will have to be rebuilt at a large expense due to being without fluid in them for a while  being 50 plus years old and the gaskets and seal drying up while out of the car without the fluid in them 

The turbo 400 trans —is so very bullet proof that I have not seen one that required rebuilding —-on this site since 2006  so I assume there is not a lot of demand for them for that reason ( new for 64 ) 

There are constantly hydromatic trans that need attention or rebuilding  of some kind over the years on this site 

The other Extremely Important issue is —you need to be replacing the same trans you now have in the car —with the same type trans that is coming out of that car ( cannot swap the two ) 

You cannot be putting —a turbo tans ( the better trans reliability wise ) in a car with a Hydromatic  the trans needs to bolt up to an engine that has ———the correct crankshaft in your engine —to be doing that 

The  engines crankshaft end on the trans side of the engine —-are different sizes for the two trans —and you will be —breaking flywheels if the  you install A turbo trans on an engine that had a Hydromatic stock 

Just trying to keep you out of some major trouble when doing trans replacement on your pride and joy 

Enjoy 

There has been a lot of heated discussion about location and shipping. I have deleted these replies as they do not help answer the question. I will just say I charge $150 for good used 1964 Turbo Hydramatics. I charge a lower rate because I do factor in the fact these are heavy and shipping can be expensive for most people. 

My suggestion if you are buying, is to factor in what it will cost you to pick up or transport the transmission.

My suggestion if you are selling, is to give as much information as you can. Include the location, weight (200 lb with torque converter or 155 lb without) and any stipulations regarding shipping (will you charge extra to strap down on a palate, do you require payment up front) . Also include as much information as you can about the condition of transmission.
- Did it come out of a good running shifting car or is that unknown.
- Is the fluid nice and pink red like new fluid, or does it have a brownish hue with a burnt smell
- Do you have any documented maintenance or rebuild on the transmission.

Also, pictures can help sell anything. When I pull one with a large % of the original Cadillac blue on the casing I always include a picture. Pictures can help sell anything as someone can actually see what they are buying. I always have a hard time sending big money for anything used when I don't have a picture. 

Price.. that is up to you. I have over a dozen for $150 sitting covered on a palate. Four are known from good runners, shifting cars. I am in central NC. I am not in a hot bed of old Cadillacs like up in the North East or California so most of mine have to be transported by a national carrier. Given the fact this is a 1 year only transmission, I would think one from a good shifting car should command over $500 ... but again I have 12 on palates. I know that probably 4 out of 5 customers that contact me for one are turned away due to shipping. That is one reason I have continued to adjust my price downward. 10 years ago I sold them for $250 each.  That is about the extent of advice I can offer. 

RSS

Photos

  • Add Photos
  • View All

Forum

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy 1 hour ago. 0 Replies

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Jason Edge 1 hour ago. 3 Replies

The weather here in winter is great for a Cadillac cruise.Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 1 hour ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Free 1964 parts before I throw them out

Started by Preston Bealle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin yesterday. 7 Replies

I have front brake drums and discs, a window, a window frame, and an air cleaner shroud. I don't need them and anyone can have them for shipping cost. I would guess the shipping would be $20-25 for…Continue

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service