I have a 64 Deville Convertible, keep running into the same problem - vapor lock on hot days. So far I have rebuilt the carburetor , new gas tank , but when it sits in traffic on a hot day it will vapor lock .  It will take about 30 minutes for it to cool down, then starts up and runs again.  My Son said dont drive it on a hot day , think that is ridiculous.

Has anyone else run into this issue?  And does anyone know of any solutions or suggestions? 

Appreciate it 

Rick McBurney

Views: 65

Reply to This

Replies to This Discussion

Wrapping the fuel line helped mine. With the ethanol in gasoline these days, it boils at a lower temperature than it use to. You can fine insulated tape for wrapping the fuel line at auto parts stores & elsewhere. It's not the prettiest thing in the world but it does solve the problem. It really only necessary between the fuel pump & carburetor. Air-conditioned cars have a fuel return line on the fuel filter housing which also help reduce vapor lock. Mine has that & with the wrapped line I no longer have any vapor lock problems.

Here's what I used: https://shop.advanceautoparts.com/p/design-engineering-cool-tape-1-...

Here's what it looks like installed:

You have most likely not fitted the correct gaskets below the carburetor.

However as our cars came with two different makes of carburetors you need to tell what you have. My guess though is that you have a Carter. They do have these problems if not using the correct gaskets in the correct order.

But, before you start fault finding go to "Help" (between Invite and Literature on top). Scroll down to:

Read it all and do remember the "shim" if you have a Carter. It's the shim that's most likely is missing in your setup.

Does your engine run hotter than it should  causing higher under hood temps that may be causing  or adding to the  vapor lock issue ?

A lean running engine will run hotter than it should be 

A plug check would show plugs burning whiter than the brown paper bag color they should be 

Ethanol fuel will burn leaner than the engine  and carb were  originally designed for 

Rejetting the carb if the above applies could help reduce heat in the cylinders and under the hood 

Enjoy 

Even if the carb was rebuilt it is still to stock specs and not recalibrated for the fuel ( ethanol ) you are now burning in the engine 

Enjoy 

All you can do to reduce under hood temps should help your problem 

A bad clutch fan or radiator that needs replacement 

Coolant that is old and needs replacement 

Lower the temp rating of your thermostat  195 to 180 — 180 to 160 

They sell coolant additives that reduce coolant system temps by 20 degrees 

Some thoughts if you establish that the engine is running on the hot side and adding to or causing your vapor lock 

Enjoy

Check the float level, as it could be set to low. The fuel will boil of faster with a low fuel level in the bowl.

You can remove the rubberized shields over the A frames for the front tires to reduce engine bay heat ( if you still have them ) 

Mine are off for years and no debri from the tires has ever been a problem entering the engine bay 

Is an old Hot Rod thing to reduce engine bay heat 

Retarded timing —-will cause your engine to run hotter so check that if  the tune is over due 

Enjoy 

For what it  is worth 

I have never had any vapor lock issues with my 64 convertibles engine and have the car off the showroom floor all these years as it was my dads car ( one of his collection of 8 - 62-64 coupes and converts all restored turn key )

I run my car often  now in 80 to 90 degree temps in Florida with the temp gauge slightly past the 1/4 mark on the temp gauge

That has me believing the problem has a solution

my 429’s performance is always a joy for me to be experiencing every time I drive the car on the very best weather days making them  a very special time 

you can help reduce the temp at the carb by removing the carb and blocking the heat passages at the front of the intake manifold  

that should reduce carb heat and vapor lock issues 

if your exhaust heat riser —-is not opening and closing Correctly that will cause the intake manifold heat passage to the carb to get much hotter than it should casing the carb to get hotter than it SB 

you can wire it open if it is not working correctly ( old Hot Rod trick ) 

Heat riser is on the driver side just below the exhaust manifold —where the exhaust pipe is connected to the manifold 

a long list of things that can be done to reduce under hood heat issues in the above posts 

my engine is completely stock with an Edelbrock carb rejetted for the fuel we now use and a point dist 

My car did not come with a clutch fan and I have had the fuel return to the gas tank disconnected for over 30 years 

hope the above helps some solve the vapor lock issue which is difficult to deal with 

RSS

Photos

  • Add Photos
  • View All

Forum

F/S 1963/1964 Cadillac parts

Started by Bob Hoffmann in For Sale. Last reply by Russ Austin 16 hours ago. 7 Replies

1963 center bumper & license guard only.1964 front bumper complete, less license guard1964 lower grille1964 cornering lightsAll these parts are from a California car.1964 dash pad. black, great…Continue

1964 Twilight Sentinel

Started by Charles Fares in For Sale 16 hours ago. 0 Replies

Complete USED Twilight Sentinel from a low-mileage, dry California car.  All components and electrical connectors present, no cut wires, nothing damaged or missing. It's plug and play. Send me an…Continue

Re jetting Carter AFB

Started by Robin Evans in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 17 hours ago. 7 Replies

Is it possible to use Edlebrock main jets and needles in a Carter AFB Carburettor. My 64 Coupe Deville runs duel straight through exhaust and this makes the mixture week in mid range and top end. How…Continue

Tags: Duel, Exhaust:, Straight, through:, Fueling:

I need to buy rim for tire Los Angeles ca

Started by Charles in Wanted to Buy. Last reply by Charles 20 hours ago. 5 Replies

in need or rim for tire Cadillac Fleetwood 64 any one known why i can buy in Los Angeles ca ..hi..thanks 310 309 0332Continue

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service