Does anyone happen to know the right gasket to use on the ventilator valve connector, where it meets the valley cover? I pulled a crusty gasket off the connector, but can't seem to find the right replacement online.

Thanks!

Views: 29

Reply to This

Replies to This Discussion

I have them new from the engine rebuild kits I have brought in over the years and sell for $3 as seen below and can ship from NC to CA 1st class letter rate (no tracking) for $2, or 1st class parcel for $4 (tracking), or 2-3 day priority (tracking) for $8 for a total of $5, $7 or $13 depending on shipping preference. Shoot me a PayPal to jasonedge@nc.rr.com and will have one on the way tomorrow morning. If you don't have PayPal email me at jasonedge@nc.rr.com and I can send an invoice so you can pay with credit/debit card.

 

It is just a round cork gasket. You can easily make one by getting a sheet of cork material from any auto parts store. be sure to use a new razor blade.

Russ is right. These are easy to make using a sheet of cork rubber gasket, a utility knife, and a steady hand. The issues is sometimes getting a good template. If you have an old gasket available the easiest method is to lay on a piece of paper and spray with rattle can paint, lift the old gasket and there is your template.  Simply overlay on the gasket material and use a utility knife to cut out. Since this is just a circle, so you can measure the inner and outer diameters and draw the circle on a piece of paper, overlay the gasket and cut out. 

Since I have the new gasket in my hand here are the specs: ID 1 3/8", OD 1 7/8", 1/8" thick, 1/4" width.
 
For small gasket projects, I like the Fel-Pro 3060 4 pack gasket set.  It's $9.39 via Amazon and if you are a Prime Member (who isn't!), it will be delivered to your door free in 2 days. I just re-upped last week. Our local AutoZone sell for $8.99 but the 40 cents savings is not worth it and I can wait 2 days! For the Amazon link Click Here. They also sell individual sheets of different gasket material. For the 4 pack set here is what is included:

One cork-rubber sheet = 10"x 8 5/8" x 1/8"
One cork-rubber sheet = 9 1/8" x 8 5/8" x 1/16"
One rubber-cellulose sheet = 9 3/4" x 8 5/8" x 3/64"
One rubber-fiber sheet = 9 1/4" x 8 5/8" x 1/32"

RSS

Photos

  • Add Photos
  • View All

Forum

Wanted: retaining clips for dash pad legs

Started by Mark Geertsma in Wanted to Buy. Last reply by Russ Austin 6 hours ago. 1 Reply

Looking for the retaining clips (L+R) that the "legs" of the dashpad snap into. Mine are missing. Continue

1964 429 & Trans For Sale

Started by Russ in For Sale 14 hours ago. 0 Replies

Anyone in need of a 429 & trans? Was running when pulled from car but had low compression on a few cylinders if memory serves me right. Engine/trans are in Phoenix. Russ, 562.858.6926Continue

Center bearing - replacement.

Started by Anders in Restoration Discussion. Last reply by Norman Silverman 18 hours ago. 22 Replies

Had some sound from the propeller shaft and as the rear wheel bearings just been replaced I thought it would be the center bearing. Removed the propeller shaft and checked the center bearing (as per…Continue

Blog Posts

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 4 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service