Wanted: 63 NSS - Neutral Safety Switch
Replies to This Discussion
-
Permalink Reply by Anders on
-
Yours might be repairable. There are some instructions in the "Help" section. However Russ Austin on this site usually will be able to repair this type of equipment.
You should also be aware that not all NSS from 1963 will fit your car. Depends on tilt/non-tilt and so on. If you remove yours you will see a number on the backside. Like 652 or similar. You need a "new" NSS with the same number. Of course you could be lucky on ebay, but Russ is usually the best solution.
-
Permalink Reply by Russ Austin on
-
What's wrong with yours? I have new sliders if the post is the only thing wrong with yours. I can usually repair the broken Bakelite if the damage is on the bottom. I repair them for 40.00
Send me and email with pictures of the damaged area. russ85747@hotmail.com
Photos
Members
Forum
Start up. 1st attempt
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 7 hours ago. 21 Replies 0 Likes
No Description
Classic Cadillac Parts For Sale - Misc Items
Started by Jason Edge in For Sale. Last reply by Jason Edge 10 hours ago. 234 Replies 13 Likes
I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue
64 Horns
Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Saturday. 1 Reply 0 Likes
I have 3 horns and the only one working is the bottom long one. The 2 round ones are not. I played around with the connections and they seem ok. I tried to check for power but not sure I was doing it…Continue
Compression test
Started by Michael Chomout in Restoration Discussion. Last reply by Karl Schwarz on Friday. 8 Replies 0 Likes
Dear Gents, just had time to dova compression test on the 429 engine by warming up the engine and removed all plugs and went through cranking without pouring oil into the cylinder since I want to…Continue
Blog Posts
63 Trunk detail
Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment 0 Likes
Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob
Car lift and jack stands
Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments 0 Likes
I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …
ContinueLeaky Freeze Plug
Posted by Lee Martin on March 22, 2021 at 12:49pm 7 Comments 0 Likes
Just developed a significant leak coming from a freeze plug right over the starter. Would this be considered a "cam plug" i.e. like Dorman 17616DS? Our cars have multiple sizes of plugs on engine block and I want to get the right one. Also, does anyone know how pricey this is for a shop to fix? Thanks!
Balancer location
Posted by Kim K Kaiser on March 20, 2021 at 4:47pm 6 Comments 0 Likes
Readi g another thread. Does this look about right on balancer gap? Thats a 1/4 thick piece of metal.
Events
-
April 2021, 1963/64 Cadillac Chapter Virtual Meet-Up via Zoom
April 18, 2021 from 7pm to 8:15pm – Zoom
0 Comments 0 Likes
© 2021 Created by Jason Edge.
Powered by
