I have a 64 coupe with the original 429. It runs great, until you try to really accelerate then it pings and i'm hesitant to accelerate. The highest octane fuel we have here in California is 91. The owners manual says to use a minimum of 100 octane. That's not that easy (or cheap) to buy these days, at least not here. Does anyone use an octane booster? Do they really work? Any other suggestions? 

Views: 97

Reply to This

Replies to This Discussion

91 would be equivalent to the old 100. There are two different ways that they measured the octane rating. Today is only one accepted method. If you have pinging then you have other problems. I would check that vacuum advance is working and holding a vacuum and timing. Also do a tune up, cap rotor and plugs, if you dont know the age of them. Do you have points or petronix ignition? 

All those parts are new and the car is tuned to the factory specs. 91 and 100 octane are definitely not the same. 91 octane (R+M/2) and 100 octane (research method) are different, by I believe 11 octane as the research method 100 octane fuel has a motor octane rating of 104 (100+104/2+ = 102). Yes, 100 (RON) octane used to be the "premium" fuel with the highest octane and now 91 is considered the "premium fuel with higher octane but 91 octane is 91 octane. The car needs 100 octane (research method as described in the owners manual). It's a fuel problem, that I know. I'm just curious how everyone else is getting around it. Octane booster, expensive 100 octane race gas, or de-tuning  the car? Rebuilt engine with lowered compression? 

I wasn't clear enough I guess. No one else is reporting problems with 91 octane fuel. I definantly don't have problems with 91 and I am running 10 degrees on my initial. This is why I suggested that the problem is else' where. How is the oil consumption? Are you using the same company's 91 or have you tried other companies? These are the only suggestions I have as this is not a common problem with this engine running 91. The fuel in 1964 was no where near as good as it is today. Octane or not, it is consistent in its quality. In 64 not so much. Modern engines and their emissions related equipment need consistent and better fuel. Just my two worthless cents, good luck. 

I'm able get 91, 95 or 98 octane and I use 95.

I'm not that sure however, that octane ratings are worked out the same way the world over.

There are no pistons that have a lower compression for our cars, 10.5 is it. My engine is rebuilt also. 

Back to my original response you MAY have other problems. Running lean or passing gear not engaging or hooked up. These are all possible solutions along with the possibility of it being a fuel problem. 

It may be a lean condition causing it to run hot at the plug, have you tried a cooler plug. 

I believe cars for export or maybe California emissions had lower compression engines, my 64 Fleetwood (a California car) has a lower compression engine according to the build sheet.

Today's pumps, at least in the USA, use an average of the old 2 octane rating methods ((Ron + Mon)/2). Using the owners manuals and what they recommended back then it works out to about 94.5 octane with today's pump values. I have never had any issues running 93 or better Octane in my 64 CDV.. before or after rebuild, and with stock carb or the Edelbrock 1411 I currently run.  However, 94.5 would be a minimum and have observed more power when I have added booster or ran higher octane rated gas.

For more details on Octane Ratings check out this Help Page topic:
- Octane Rating Information
 

I guess our tar sands fuel is better than your Texas tea fuels LOL. I do have access to 94 but dont find much if any difference running the 91. The 94 is only at one or two companies and all they do to increase the octane rating is add more ethanol. The distance and effort it takes to get to it isnt worth it. I dont have a carburetor I'm fuel injection. 

I'm running 93 octane in my 63 Coupe DeVille without pinging. I did have a pinging issue in another car (79 Trans Am with 400 SBC). That turned out to be too hot spark plugs. Cooler plugs solved that one.

The cars built for oversea's had the lower compression pistons put into the engines.

Russ, have you seen the pistons available? I have found none doing various online searches. 

I have not, but I have not been looking for them.  I did see an NOS set one time.

RSS

Photos

  • Add Photos
  • View All

Forum

Photo posting appears to be broken

Started by Kevin Campbell in General Discussion 5 minutes ago. 0 Replies

Hey Jason,It would seem, the photo posting bit could do with a tickle on the bottom to get some action happening. I understand, you're probably still making like a friggin gopher in one of your…Continue

Where to get brake booster and master cylinder rebuilt

Started by Chris Gill in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Campbell 20 minutes ago. 1 Reply

Hi folks,I'm new to Cadillacs so bear with me if this question has already been answered but I did a search of the forum and couldn't find an answer.It appears I have an original master cylinder…Continue

1964 Cadillac Coupe for sale

Started by Hank Johnston in For Sale. Last reply by Kevin Campbell 54 minutes ago. 4 Replies

Hi fellas, regretfully I am trying to sell my 1964 Cadillac Coupe deville. I've had it almost 4 years now and am having to face facts that I just dont have the time or money to do what I want with…Continue

Question: comfortable highway speed?

Started by Mark Geertsma in General Discussion. Last reply by Jeff Kinzler 13 hours ago. 19 Replies

What is your preferred cruising speed on highways with your classic Cadillac? What I mean is the speed that allows for relatively quiet and comfortable cruising without slowing down other traffic.…Continue

Tags: speed, Highway

Blog Posts

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 2 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Fuel loss in Carburetor

Posted by Ian Osborne on December 29, 2018 at 11:24pm 16 Comments

Lately if I haven't started my '63 in four or five days it seems that the carburetor has gone dry. The starter cranks for an extended period of time and the engine doesn't come close to firing. I have resorted to pouring a little fuel into the carb to save the starter and battery. This gets it started and it runs fine. It also starts fine after sitting a short while - a couple hours or so.

The fuel pump is new and there is always fuel in the glass bowl of the fuel filter. This, along…

Continue

interior

Posted by John Rueff on December 19, 2018 at 4:24pm 3 Comments

I would like to upholster my caddy back to original.   Does anyone know where I can look at some pictures or photos.  Also, how hard is it to remove the dash?  thanks

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service