I have a 64 coupe with the original 429. It runs great, until you try to really accelerate then it pings and i'm hesitant to accelerate. The highest octane fuel we have here in California is 91. The owners manual says to use a minimum of 100 octane. That's not that easy (or cheap) to buy these days, at least not here. Does anyone use an octane booster? Do they really work? Any other suggestions? 

Views: 127

Reply to This

Replies to This Discussion

91 would be equivalent to the old 100. There are two different ways that they measured the octane rating. Today is only one accepted method. If you have pinging then you have other problems. I would check that vacuum advance is working and holding a vacuum and timing. Also do a tune up, cap rotor and plugs, if you dont know the age of them. Do you have points or petronix ignition? 

All those parts are new and the car is tuned to the factory specs. 91 and 100 octane are definitely not the same. 91 octane (R+M/2) and 100 octane (research method) are different, by I believe 11 octane as the research method 100 octane fuel has a motor octane rating of 104 (100+104/2+ = 102). Yes, 100 (RON) octane used to be the "premium" fuel with the highest octane and now 91 is considered the "premium fuel with higher octane but 91 octane is 91 octane. The car needs 100 octane (research method as described in the owners manual). It's a fuel problem, that I know. I'm just curious how everyone else is getting around it. Octane booster, expensive 100 octane race gas, or de-tuning  the car? Rebuilt engine with lowered compression? 

I wasn't clear enough I guess. No one else is reporting problems with 91 octane fuel. I definantly don't have problems with 91 and I am running 10 degrees on my initial. This is why I suggested that the problem is else' where. How is the oil consumption? Are you using the same company's 91 or have you tried other companies? These are the only suggestions I have as this is not a common problem with this engine running 91. The fuel in 1964 was no where near as good as it is today. Octane or not, it is consistent in its quality. In 64 not so much. Modern engines and their emissions related equipment need consistent and better fuel. Just my two worthless cents, good luck. 

I'm able get 91, 95 or 98 octane and I use 95.

I'm not that sure however, that octane ratings are worked out the same way the world over.

There are no pistons that have a lower compression for our cars, 10.5 is it. My engine is rebuilt also. 

Back to my original response you MAY have other problems. Running lean or passing gear not engaging or hooked up. These are all possible solutions along with the possibility of it being a fuel problem. 

It may be a lean condition causing it to run hot at the plug, have you tried a cooler plug. 

I believe cars for export or maybe California emissions had lower compression engines, my 64 Fleetwood (a California car) has a lower compression engine according to the build sheet.

Today's pumps, at least in the USA, use an average of the old 2 octane rating methods ((Ron + Mon)/2). Using the owners manuals and what they recommended back then it works out to about 94.5 octane with today's pump values. I have never had any issues running 93 or better Octane in my 64 CDV.. before or after rebuild, and with stock carb or the Edelbrock 1411 I currently run.  However, 94.5 would be a minimum and have observed more power when I have added booster or ran higher octane rated gas.

For more details on Octane Ratings check out this Help Page topic:
- Octane Rating Information
 

I guess our tar sands fuel is better than your Texas tea fuels LOL. I do have access to 94 but dont find much if any difference running the 91. The 94 is only at one or two companies and all they do to increase the octane rating is add more ethanol. The distance and effort it takes to get to it isnt worth it. I dont have a carburetor I'm fuel injection. 

I'm running 93 octane in my 63 Coupe DeVille without pinging. I did have a pinging issue in another car (79 Trans Am with 400 SBC). That turned out to be too hot spark plugs. Cooler plugs solved that one.

The cars built for oversea's had the lower compression pistons put into the engines.

Russ, have you seen the pistons available? I have found none doing various online searches. 

I have not, but I have not been looking for them.  I did see an NOS set one time.

RSS

Photos

  • Add Photos
  • View All

Forum

FUEL GAGE

Started by STEPHEN HORWATH in General Discussion. Last reply by Tony and Ginny 429 10 hours ago. 7 Replies

Hi just wondering if anyone else had a problem with their fuel gauge going up to full when key is turned to the on position or when the car is running.  it goes back to empty when key is in the off…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 23 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Front Window Motor Installation Help Needed

Started by Roy in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 9 Replies

I have a bad window motor in the passenger side door.  I have removed the door panel and am at a complete loss as to where to start and what to do from here.  Does anyone have any step by step…Continue

Intake manifold leak

Started by Joe DiIaconi in 1963/64 Cadillac Specific Discussion. Last reply by Roland Moser yesterday. 35 Replies

Anyone install better quality intake manifold gaskets?

Blog Posts

Hood Insulation

Posted by Dominic Salemi on July 3, 2019 at 9:15pm 2 Comments

Can anyone give me some information on what to use to secure my hood insulation to the hood.

Thanks

Dominic

64 Hood Hinge Color?

Posted by Bob Schles on June 27, 2019 at 4:46pm 2 Comments

Can someone tell me what color the hood hinges should be? I've seen both silver and gold cadmium plating colors on the cars. Thanks

Rear Side Window Stainless Sill Removal

Posted by Lee Martin on June 24, 2019 at 3:07pm 2 Comments

I'm looking to replace a piece of the stainless trim that sits on the outside of the car like a sill outside the rear passenger side window.  I can just barely see one screw at one end but does the door panel and/or window need to come out to access this?  If anyone has done this I'd like to learn what is involved.  Here's a photo of the piece I'm talking about:…

Continue

Cadillac Returns to its Roots Under New Leadership

Posted by Jeff Kinzler on May 1, 2019 at 12:30am 3 Comments

Cadillac’s new boss says they should stop trying to build BMWs and go back to building Cadillacs again.

What do you think? 

https://carbuzz.com/news/cadillac-finally-admits-what-everyone-knew-for-years

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service