Hello and greetings to all Cadillac Enthusiasts.

I am pleased to be a new Member of this Chapter and thank you to everyone for having me here.

A Question on the Weatherstrip Window / Doors:

Rubbertherightway offers a pre cut 8 Piece Kit and states it is as close to original as it can be

Steelerubber seem to have 3 different Versions.

Does anyone has experience with either one as far as quality and fitting?

is there maybe an existing vendor, i may not know of yet?

I'd appreciate any advise .

Thank you 

Best Regards

André

Views: 104

Reply to This

Replies to This Discussion

I have installed the outer scraper seals that Steele Rubber sells but never the inner felt. Most of their stuff is very high quality and they stand behind it.

Thank You Jason for the Feedback. I'll certainly consider. Yes Steele Rubber is known for there Quality, though "rubbertherightway" seem to have original reproduction custom cut to fit in, including the proper notch to vent the windows. i'll give them a call monday and see.

Have a great Day

RSS

Photos

  • Add Photos
  • View All

Forum

fuel pump

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Anders 1 hour ago. 4 Replies

I am gathering up some stuff to put away for the potential trip home in oct/nov from MT to MS in the 63 cdv.i thought a fuel pump may be a good piece to have nearby,  Are the newer ones like you can…Continue

off the wall question

Started by James Fejerang in 1963/64 Cadillac Specific Discussion 1 hour ago. 0 Replies

 Could anyone please tell me why on some models of the 64 devilles, the Bezel, Turn signal (LH upper) is clear and the other one RH Bezel is chrome.  Sorry if this is a stupid question, but i have…Continue

rear seat speaker grill

Started by Kenneth R Hudgins in 1963/64 Cadillac Specific Discussion 10 hours ago. 0 Replies

Looking for a rear seat speaker grill for my 63 EldoradoContinue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 159 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service