Chapter Shirts

Chapter Shirts Available!!

These are top quality "Gildan Ultra Cotton" pre shrunk shirts. The color is ash grey which will go great with just about anything color pants or jacket, especially a dark jacket or dark pants.


I am selling these “at cost” + shipping

• The cost for shirts sized S to XL is $15, the 2XL is $17 and the 3XL is $18.

• If interested in one of our Club Shirts send me an email at jasonedge@nc.rr.com

  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on May 9, 2016 at 1:05pm

NOTE: I am getting very low on Chapter Shirts. If you want one as the summer approaches now is the time to order. Here is my current inventory:

 0 - Small, 1 - Medium, 2 - Large, 5 - XL, 0 - XXL, 2 – XXXL
The cost for shirts sized S to XL is $15, the 2XL is $17 and the 3XL is $18.

If you want one, email me at jasonedge@nc.rr.com

Comment by Jason Edge on November 5, 2015 at 11:32am

Above and Below CLC Western Region VP Phil Terry models our Chapter shirt

Before leaving for the Grand National this year, I had run out of XL's and almost out of L's, and ordered another batch of chapter t-shirts.   I have to order a minimum to be able to get at the $15 cost for S thru XL, and this go round I had to order a minimum of 35 shirts or $525 out of pocket.

These are the best batch yet with really vivid colors, in the crest and logo. PKD owner Paulette Disbrow personally did this batch and did the whites last as she says that really makes it stand out. I will try to get some pictures later but they are the same shirts you have seen before, just better.

The Ash Grey goes with anywhere and make great gifts to spouses, the kids, nieces, nephews, etc.  Or, if yours is a bit faded and want a crisp new t-shirt, this is the time to get them as it will probably be another year before I order another batch so once your size is gone they are gone!

I have a large stock right now and would prefer to have these shirts on the back of our members instead of in a box up in my office. I also wouldn't mind filling the hole in my wallet the last order left.

My current inventory of chapter shirts includes:
1 Small, 5 Medium, 9 Large, 6 XL, 1 XXL, 3 XXXL

Again, I am simply passing on my cost to you guys on the chapter shirts. 
The cost for shirts sized S to XL is $15, the 2XL is $17 and the 3XL is $18.

If you need one please email me at jasonedge@nc.rr.com and provide size, quantity, and ship to address.  

Photos

  • Add Photos
  • View All

Forum

Back to Starter

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 1 hour ago. 36 Replies

Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag…Continue

Been busy

Started by Clovis in General Discussion. Last reply by Jason Edge 2 hours ago. 3 Replies

I haven't spent much time on my old cars this summer. My latest project has been a gazebo on the new island. I'll be ready Wednesday to start putting on shingles. Tomorrow its facia and some more…Continue

Here's some what a update on the engine!

Started by Haris dizdarevic in General Discussion. Last reply by Jason Edge 13 hours ago. 7 Replies

Continue

Blog Posts

HVAC Vacuum Valve Clip-need the one for the Power Control side

Posted by Norman Silverman on September 17, 2018 at 8:15pm 4 Comments

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy…

Continue

7 vacuum valve-need a good one or someone to recondition mine

Posted by Norman Silverman on September 15, 2018 at 5:44pm 12 Comments

So, I've put my 7 vacuum valve from the control head side to the test, and it failed. I looked at the instructions for re-conditioning it and unless I am missing something, the instructions are missing something (about how to take off the clip that provides the tension that holds the two pieces together). 

In any case, I can't do this particular repair so I am looking for a new valve (not likely), or a good re-conditioned one, or someone who has done this before and would do mine for…

Continue

Mosiac Cadillac emblem Table

Posted by Dana G Cooper on August 30, 2018 at 10:48pm 11 Comments

Wanted to share a picture of a table my wife made for me to display with our 63 Coupe Deville. 

Inside door handle thread size

Posted by Michael Jarnagin on August 23, 2018 at 4:31pm 1 Comment

Anyone know the thread size on the inside door handle bolts mine are missing any info much appreciated 

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service