Enjoying the view (GN 2017)

Views: 94

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Russ Austin on June 4, 2018 at 7:38am

Clifford, can I save this picture for possible use in the calendar?   A high res picture would be best sent to my email.  russ85747@hotmail.com 

Comment by Russ Austin on June 4, 2018 at 7:37am

Very good picture to add to the possibilities for the 2019 63/64 Cadillac calendar.   What ever condition your car is, take a few good pictures and send them to me;  russ85747@hotmail.com 

Comment by Clifford Muskus on January 16, 2018 at 8:13pm

Thanks for the comments! This shot was taken during the caravan tour to USA Parts Supply in Kearneysville, WV in August 2017 at the Grand National event. In the background you can see the Shenandoah Valley. This will be the most northern part of the valley with Harpers Ferry on your far left. Beyond those mountains lies the state line between West Virginia and Virginia. 

Comment by Kevin Campbell on January 16, 2018 at 12:33am

Bee-You-Tee-Full view..... oh, the trees and valley is nice too, but no where as nice as the 64

Comment by Jason Edge on January 16, 2018 at 12:31am

Which Valley? Details? Great shot!

Photos

  • Add Photos
  • View All

Forum

A Drilling No-No .... That Worked!

Started by Jason Edge in General Discussion. Last reply by Jason Edge 1 hour ago. 16 Replies

Thought I would share a quick story regarding something I did that I generally do not recommend - Free handed drilling a broken front engine cover bolt.  Before I jump into it I will say I do not…Continue

Exhaust manifold: Repair, replace or headers?

Started by Dutch Dickinsen in General Discussion. Last reply by Tony and Ginny 429 6 hours ago. 1 Reply

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue

Tags: 429, manifold, exhaust

Steering Wheel

Started by Mark Borer in General Discussion 11 hours ago. 0 Replies

plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue

Help! I need a 1964 Eldorado front left fender.

Started by Jorge M in Wanted to Buy. Last reply by Jon Ettman 13 hours ago. 5 Replies

Help looking for a 1964 Eldorado front fender for a convertible.Thank you please contact djjmoreno84@gmail.comContinue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 6 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service