Ric Walter
  • Male
  • Mertztown, PA
  • United States
Share on Facebook

Ric Walter's Friends

  • jeremy walter
  • Frank Vollaro
  • Russ Austin

Ric Walter's Discussions

Por15 Fuel Tank Restore Kit

Started this discussion. Last reply by Ian Osborne Jul 7, 2017. 3 Replies

Has anyone used Por15's Fuel tank Restore?? Is it any good?? Does it work?Continue

Engine timing after electronic ignition conversion

Started this discussion. Last reply by Tony and Ginny 429 Mar 5, 2017. 12 Replies

I converted my ignition with the pertronic kit 1181 ignitor conversion kit. Now when the timing is at 5 deg the engine runs very rough, to run good the timing needs to be advanced 23 at idle. I…Continue

63 Fuel Pump

Started Sep 30, 2016 0 Replies

I am looking for a 1963 series 62 with 390 ci machanical fuel pump. Please email me at paguy22@dejazzd.com if you have one and the cost with shipping.Continue


Ric Walter's Page

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
1963 Series 62 Convertable
Cadillac LaSalle Club Member? If Yes, Membership #?
1963/64 Cadillac Chapter Member?

Ric Walter's Photos

  • Add Photos
  • View All

Ric Walter's Blog

TV Rod Adjustment HELP!

Posted on May 18, 2016 at 10:20am 1 Comment

I can't seem to find passing gear. I put on a new Edelbrock carb and had to make an adapter for the TV rod. I adjusted the throttle rod and have full movement into the secondaries, but no passing gear. Anyone have any suggestions??

Crossover water pipe O ring

Posted on September 15, 2015 at 9:05am 5 Comments

Anyone have any tricks to seat the O ring properly after replacing the water pump ??? I have a small weeping from the O ring area.

Paint or Not to Paint

Posted on June 29, 2014 at 10:52pm 5 Comments

I just started going to cruse nights and shows in my area with my 63 series 62 convertible. I have surface rust over the front hood, rear trunk lid and left front 1/4 panel. I being told not to repaint and destroy the patina of the car because it is original paint. They tell me to wet sand a clear coat the car..I'm looking for opinions on this. …


connecting & adjusting tv rod to edelbrock 1406 on a 1963 series 62

Posted on October 22, 2013 at 11:02pm 2 Comments

New to the world of Cadillac!! Need help and suggestions. tried making a bracket to match rochester setup. Does the 63 hydramatic have a passing gear or is it only 4 forward and reverse gears?

Comment Wall (1 comment)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 11:21am on July 29, 2013, Jason Edge said…

Welcome to the 63/64 Cadillac Website.  

Be sure and check out all the links and pages and make yourself at home.  




  • Add Photos
  • View All


Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 38 minutes ago. 161 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts


Started by Jason Edge in Chapter Discussion 3 hours ago. 0 Replies

Ok.. How about one more scan for today from the 1964 Cadillac Mailer I will be including in an upcoming newsletter.…Continue

Discover a New Measure of Automobile Pleasure!

Started by Jason Edge in Chapter Discussion. Last reply by Tony and Ginny 429 6 hours ago. 1 Reply

OK. I'm having fun with this mailer I have scanned in. Cadillac sure had a way with describing their cars back in the day! Here is the back cover of the 6 page mailer you will seen in an upcoming…Continue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …


Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…


Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.



Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…



  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service