I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.

Views: 58

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Gene McIlroy on August 12, 2019 at 11:51pm

Jason, I appreciate you correcting the post.  Not a problem at all I tried but just could not figure it out.  Thanks

Comment by Jason Edge on August 12, 2019 at 8:32pm

Gene, I usually don't mess with anyone's post but took the liberty to correct your post by swapping out the correct picture. When you post from a desktop/PC you just click Edit up top to make changes. If on a mobile device you will need to make sure you are in "desktop view" to make the edits. There is a drop down menu when on mobile devices where you can select desktop view. This might not be your issue but feel it is always worth repeating for the ever growing number of mobile device users. I tend to "look" at stuff on my iPhone but post and edit stuff on the desktop .. but that's just me.

Comment by Jason Edge on August 12, 2019 at 8:28pm

Gene, Thanks for the alternate source. This one piece of rubber that holds up pretty well as seen by your original sample but always good to find new rubber replacements.

Photos

  • Add Photos
  • View All

Forum

F/S 1963/1964 Cadillac parts

Started by Bob Hoffmann in For Sale. Last reply by Russ Austin 1 hour ago. 7 Replies

1963 center bumper & license guard only.1964 front bumper complete, less license guard1964 lower grille1964 cornering lightsAll these parts are from a California car.1964 dash pad. black, great…Continue

1964 Twilight Sentinel

Started by Charles Fares in For Sale 1 hour ago. 0 Replies

Complete USED Twilight Sentinel from a low-mileage, dry California car.  All components and electrical connectors present, no cut wires, nothing damaged or missing. It's plug and play. Send me an…Continue

Re jetting Carter AFB

Started by Robin Evans in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 7 Replies

Is it possible to use Edlebrock main jets and needles in a Carter AFB Carburettor. My 64 Coupe Deville runs duel straight through exhaust and this makes the mixture week in mid range and top end. How…Continue

Tags: Duel, Exhaust:, Straight, through:, Fueling:

I need to buy rim for tire Los Angeles ca

Started by Charles in Wanted to Buy. Last reply by Charles 5 hours ago. 5 Replies

in need or rim for tire Cadillac Fleetwood 64 any one known why i can buy in Los Angeles ca ..hi..thanks 310 309 0332Continue

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service