I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.

Views: 58

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Gene McIlroy on August 12, 2019 at 11:51pm

Jason, I appreciate you correcting the post.  Not a problem at all I tried but just could not figure it out.  Thanks

Comment by Jason Edge on August 12, 2019 at 8:32pm

Gene, I usually don't mess with anyone's post but took the liberty to correct your post by swapping out the correct picture. When you post from a desktop/PC you just click Edit up top to make changes. If on a mobile device you will need to make sure you are in "desktop view" to make the edits. There is a drop down menu when on mobile devices where you can select desktop view. This might not be your issue but feel it is always worth repeating for the ever growing number of mobile device users. I tend to "look" at stuff on my iPhone but post and edit stuff on the desktop .. but that's just me.

Comment by Jason Edge on August 12, 2019 at 8:28pm

Gene, Thanks for the alternate source. This one piece of rubber that holds up pretty well as seen by your original sample but always good to find new rubber replacements.

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 16 hours ago. 164 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Looking for 64 to 66 seat belt buckles, male and female together.

Started by Ryan Frawley in Wanted to Buy. Last reply by Tony and Ginny 429 18 hours ago. 5 Replies

Hey all, I am in the process of finishing up my 64 coupe deville and noticed that the front seat belts only have the retractor side in the bag I put all the belts in when I got it. I have found it…Continue

Tags: buckle, safety belt, seatbelt, seatbelts

Movie Star Cars.

Started by Kevin Campbell in General Discussion. Last reply by Kurt yesterday. 17 Replies

We have the Village Roadshow film studios about an 1.5 hour drive away.They've put out a call for cars to appear in a movie about Elvis. :-)So, I nominated our 64 Fleetwood as a potential "Movie Star…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service