Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Views: 142

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on October 9, 2019 at 8:13pm

I didn't even paint my dash or what is left of it when all else is removed. I took the glove box door, lower dash panel with ash tray, steering column and piece over column with ignition switch to my paint guy and had him paint them. I was lucky that what is left was in pretty decent shape and was able to match up the color very closely.

Comment by Russ Austin on October 9, 2019 at 6:22pm

I painted the dash in my 63 Hearse. I left the dash in, but removed the instrument cluster, radio faceplate and AC control head.  

Comment by Jason Edge on October 9, 2019 at 2:01pm

It would be hard to describe everything from memory but Russ hits most of the biggies. Of course you want to remove the dash pad and lower dash cover, and removing the steering wheel and column will definitely make it easier. There is a large center upper bracket, vacuum hose connections, radio antenna, and a few other odds and ends but if you go slow it is not that bad.  When I part a car out I use a long flat screwdriver to disconnect the vent ducts and push them back a bit so they do not tear, and remove all of the metal dash body brackets except the top end brackets on the far left and right. As I disconnect things and am ready to remove the dash I have a large towel or blanket on my lap and lift the dash up and off the top end brackets and lay the dash in my lap. I have tools in hand such as pliers, small and large screw drivers and 1/4" socket for the Bowden cable bracket and WD40.  I use a small screwdriver to slip thru the open end of wiring connectors and a pliers to pull from the other end, and WD40 to lube it up a bit. Once I have the dash on my lap and everything disconnected I simply slide it out to one side as one assembly.  You said your seats are out... so this might not work as well for you. But for me I just sit the dash down in my lap with tools at hands reach. That's the way I have probably done it for the last 50 parts cars!

Comment by Jake Mickley on October 9, 2019 at 11:50am

Thanks Russ,

This may it may not be a winter project.  Haven't decided yet but I'm thinking it might be easier at the moment assum the seats are ito getting redone.

--Jake

Comment by Tony and Ginny 429 on October 9, 2019 at 10:40am

Hey Joe D 

I was just thinking the other day Joe’s car must be running good he has not been around for a while 

Enjoy 

Comment by Russ Austin on October 9, 2019 at 8:00am

Disconnect the wire harness to the ignition switch. Disconnect the wire harness that clips to the bottom of the fuse panel.  Disconnect the wire harness plugs on the L and R side of the dash that plug into the kick panel connectors.  Remove the dash. Disconnect the speedometer cable. Disconnect all elec plugs to the AC/heat system. Disconnect all bowdens cables to the AC/heat system.  Disconnect the AC duct and defrost hoses.  It is best to remove the steering wheel so you don't have to muscle the dash over the column.  Don't forget the shift indicator.  

2 brackets on the bottom,, and 2 brackets on top.  There is a center support rod at the bottom. 

Go slow and look for wires still attached.  I went off of memory here.

Comment by Joe DiIaconi on October 9, 2019 at 7:57am

Oh wow yes I misread, you have to forgive me it's early. I've never done that but I'm sure someone has. Good luck

Comment by Jake Mickley on October 9, 2019 at 7:54am

Thanks Joe, however I am taking about the complete dash, not just the cover.

Comment by Joe DiIaconi on October 9, 2019 at 7:52am
I have a 64, but I'm sure the 63 is closed to the same thing. First you remove the window trim on either side of the dash. Then there are three screws above the instrument cluster. Then there are I believe two or three bolts n the glove box. Stick your hands in the defrosting Vents and pull towards yourself.

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service