DOES ANYONE HAVE A SPECIFICATION OR MANUFACTURER NUMBER FOR A CURRENTLY AVAILABLE MUFFLER THAT WILL FIT A 1964 ELDORADO?

IT SEEMS TO BE A UNIVERSAL PART FROM  WHAT I SEE  AVAILABLE ON LINE, BUT THE SELLERS ASK YOU FOR THE LENGTH, INLET AND OUTLET SIZE, OFFSET, ETC. STATING THAT THE APPLICATIONS ARE NOT VEHICLE SPECIFIC. 

ALSO IS THERE A SOURCE FOR THE RUBBER INSERTS FOR THE EXHAUST HANGER/BRACKETS?

THANKS,

JEFF KINZLER

Views: 203

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on June 30, 2016 at 10:14am
Clovis, I had duals previously, but went back to factory style exhaust, sourced through Classic Exhaust out of Ohio, about 3 1/2 years ago.
Comment by Clovis on June 30, 2016 at 10:02am
Jason, I thought you had dual exhaust on your car? If you do did you get it from Classic exhaust?
Comment by Jeff Kinzler on June 29, 2016 at 4:12pm
Jason
I just ordered it from Bob at USA Parts Supply. The prices are out of date but it was 110 plus shipping. $132 all in.

He no longer stocks them but has them made up in Ohio. Probably buys from Waldron ir Classic. As they used to say "all roads lead to Rome."
Thanks.
Comment by Jeff Kinzler on June 29, 2016 at 3:55pm
Thanks for the tip. As far as I know all is original and I am trying to do some damage and cost control to status quo ante following the disastrous untuning of the engine by the rebuild shop resulting in a massive backfire.
Comment by Jason Edge on June 29, 2016 at 3:50pm

USA Parts & Supply has the mufflers listed for $84.50. I would assume they would be the original style/size muffler.  When you ask for spec for a muffler that will FIT A 1964 ELDORADO, I am assuming you are keeping everything factory.  If going aftermarket you can pretty much run almost any muffler out there ... it just has to match the diameter of the tail pipe being used. I've pulled In parts cars with tube mufflers, offset mufflers, single chamber mufflers, multi chamber mufflers, even one with those Thrush Mufflers we use to like to put on hot rod cars... well the poor hot rodders cars. Your muffler shop should be able to recommend & source a good replacement muffler, hangers, etc.

Comment by Jeff Kinzler on June 29, 2016 at 3:01pm
Thanks. I just left a message with Classic as their web site is useless.

I was looking for a specification for an off-the-shelf rather than custom fabrication part.

I just got a quote of $176 from Caddy-parts.com who has them fabricated to order. OPG has them for around $100+but seems to be non oem type i.e. noisier..
Comment by Jason Edge on June 29, 2016 at 2:39pm

I bought my complete setup, including the muffler from Classic Exhaust out of Ohio. Here is their contact info: Classic Exhaust Inc - www.classicexhaustinc.com/
Original Exhaust systems, 440-466-5460, classicexhaust@windstream.net

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Battery, alternator not charging

Started by Keith Benning in 1963/64 Cadillac Specific Discussion. Last reply by Keith Benning 13 hours ago. 10 Replies

Hello All, after replacing the voltage regulator, alternator, checking and replacing wires to alternator plug, test voltage on battery, good, voltage on alternator good.  Checked ground with multi…Continue

'64 Cadillac speedometer cable - transmission to cruise control box

Started by Don Moyer in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 19 hours ago. 3 Replies

Hi folks - I'm new to this forum, but have owned my '64 convertible since 1993.  I recently replaced the speedo gear and seal in the transmission due to fluid leak, and noticed that the end of the…Continue

1963 transmission dipstick tube came out

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 1 Reply

I went to check the fluid in the transmission on my 1963 Series 62 convertible and when I pulled on the dipstick ring the whole tube came out. I got it back in the hole, sort of, but it is loose.…Continue

Blog Posts

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Roof motor

Posted by Dermot Robinson on August 11, 2019 at 8:44am 2 Comments

Replacing my convertible roof motor.

Has anyone any experience or advice on replacing the roof motor on a 1964 Cadillac Deville .

Please..

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service