Hi every one,

After a long time rebuilding my 63 convertible, i finaly get on the road.

A question if anyone can help me. Can somebody tell me the lenght of the motor oil stick.

the cap was probably broken and welded by the old owner. but i m not sure it's in the right place

i put the right amount of oil in motor, but for the weekly maintenance i would like to do two mark "full and add oil"

So i need the lenght from de cap to the two mark

Thanks a lot 

(sorry for the poor language it's well know that french people are issued with english especially technical english...)

Views: 43

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Florentin loic on April 5, 2018 at 2:51am
Thanks Jason for your return, i will check my stick lenght.
Comment by Jason Edge on April 4, 2018 at 8:57am

The original dipstick is approx. 20" from the top of cap down to the tip.  If measuring from the bottom side of the cap you can subtract about 1/8" for a total of approx. 19 7/8". From bottom of cap, it is about 16 7/8” to the top ‘Full’ line and 17 3/4” to the ‘Add One Quart’ line.

Photos

  • Add Photos
  • View All

Forum

Replacement trunk lid

Started by Joe DiIaconi in Restoration Discussion. Last reply by Christopher Codd 1 hour ago. 19 Replies

 got got my…Continue

Wits end!

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 36 Replies

Well,  after the tire change, car running good......... then on a pleasure cruise for abour 35 miles to my destination.   25 miles in, back end vibration came back home to roost.  I was goung 55 to…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Brakes Went Out

Posted by Christopher Codd on August 8, 2018 at 8:25am 18 Comments

My '64 Cadillac DeVille had been sitting for awhile while I was travelling this summer and when I came home it had some issues starting. After replacing the plugs and the ignition coil, it was running better than it had in a long time but the brakes were sticking. I noticed the brake pedal was traveling a little farther than usual when slowing down. Soon after I noticed a hissing noise coming from around the brake pedal. Then I lost the brakes pretty much completely. I couldn't find any…

Continue

Tom and Dwight's excellent 64 Fleetwood tales

Posted by Norman Silverman on July 29, 2018 at 2:52pm 1 Comment

Wow, what a great recitation of events-and what a magnificent restoration. 

Thanks for providing a most pleasurable read.

Norm

Comfortron AC trouble shooting

Posted by Norman Silverman on July 23, 2018 at 8:54pm 5 Comments

OK, here we go.....

I got the book to troubleshoot the system. INDISPENSABLE to this effort. 

As I do a cursory exam, I see that the AC RECIRC SOLENOID is Cracked (the WHITE one in the engine compartment coming out of the HVAC body with two vacuum hoses on it). I tried to patch it up (cracked all around the base), but it does not look like it will hold. 

PLEASE TELL ME THAT REPLACING THIS PART IS NOT AS DIFFICULT AS I THINK IT IS, But I think it is a bear to…

Continue

A/C Issue / Stumped !

Posted by Dana G Cooper on July 23, 2018 at 6:29pm 37 Comments

My 63 CDV factory A/C was trash so I replaced every part in the system and converted to R134 . I also installed a STV bypass kit which eliminated the STV all together and converted the system to a cycling system.  I vacumed and charged the system with 36oz of 134. The system is cycling as it should and the pressures are right at 250 high side, cycle off at 25lbs and cycle back on at about 35lbs. It is making plenty of water on the low side hoses and evaporator drain. There is very good air…

Continue

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service