Rick Wallace's Comments

Comment Wall (1 comment)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 7:22am on August 11, 2018, Jason Edge said…

Welcome to the 63/64 Cadillac Website.

This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the Chapter. 

- Click on www.join.6364cadillac.com for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club

Be sure and check out all the links and pages and make yourself at home. The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 9 hours ago. 158 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Trunk Pull-down

Started by Brian and Dorothy Lewis in Restoration Discussion. Last reply by Jason Edge 9 hours ago. 9 Replies

Hi gang.  While reviewing the extensive photo archives on this site, I came across an excellent series of photos documenting a trunk pull-down assembly posted by Jason Edge.  I really didn't even…Continue

Exhaust manifold: Repair, replace or headers?

Started by Dutch Dickinsen in General Discussion. Last reply by Jason Edge 10 hours ago. 4 Replies

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue

Tags: 429, manifold, exhaust

Steering Wheel

Started by Mark Borer in General Discussion. Last reply by Tony and Ginny 429 11 hours ago. 1 Reply

plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service