Tyler
  • Mount Pleasant Mills, PA
  • United States
Share on Facebook
Share

Tyler's Friends

  • ian arnold
  • Jason Edge

Tyler's Discussions

Hanging doors

Started this discussion. Last reply by Russ Austin Jun 7, 2018. 1 Reply

Anyone know how to hang these doors by yourself. Any tricks?Continue

Rear Crossmember

Started Jun 11, 2015 0 Replies

Does Anyone have a picture of the rear cross-member underneath the trunk? It goes from each side of the car acts like a body support. Its welded on top of the horizontal peace of the frame where the…Continue

lower front bumper ends??

Started this discussion. Last reply by William Cameron Oct 23, 2015. 16 Replies

Well friends, i too have become a victim of the rotted front bumper ends. my body shop cannot locate one for a year and half. If anyone has a lower driver side bumper bucket for 1964  that it car…Continue

aluminum anodizing

Started this discussion. Last reply by Those Meddling Kids Apr 10, 2015. 1 Reply

Anybody know or have experience on how to remove aluminum anodizing using g a sort of acid or solvent?

 

Tyler's Page

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
1964 Sedan De Ville fordor hardtop
Cadillac LaSalle Club Member? If Yes, Membership #?
no
1963/64 Cadillac Chapter Member?
64 Cadillac

Tyler's Photos

  • Add Photos
  • View All

Comment Wall

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

  • No comments yet!

Tyler's Blog

Sticking Valve ?

Posted on September 24, 2015 at 7:45pm 2 Comments

OKay i hjvae 64 deville turbo trans. recently installed a Holley 600 cfm carb to it after the intake manifold was fixed by deleting choke tube. but because i put new heat riser on years ago and it was pricey i didnt cover the exhaust ports up to the intake. just installed new vacuum advance and ignitor 1 ignition module. But the carb and ignition seem to be okay but the fluctuating manifold vacuum ( 18 to 21 HG fluctuating) i keep getting is telling me there is a sticking valve. OR i missed…

Continue

Carburetor

Posted on August 26, 2015 at 3:50pm 34 Comments

Well my friends looking for a little advice. the old Rochester has well; seen better days.it leaks around all the gaskets after i just replaced them all. I have a 600 cfm Holley off an old Mopar thinking about putting it on the 64 SDV. Just wondering if anyone has experimented with the holleys on these cars? it wokrs great on the Mopar 360 cubic inch just not sure about the spacers and gaskets i need. A question for jason is did you use JB weld for the choke tube hole or whats your thoughts…

Continue

trunk to bumper filler

Posted on July 7, 2015 at 9:09pm 2 Comments

Does anyone know if there is a peace that goes between the bumper and the trunk. So you can't see down to the road when you open the trunk. Mine doesnt have anything wondered if there should be?

BIG News!

Posted on July 1, 2015 at 11:08pm 3 Comments

Picked my car up today from the body shop after it had been there 3 years and still not done.strapped her down drove and hour and wouldn't you know?.... I managed to puncture the fuel tank with the tow hook. So I m probably I need of a new fuel tank. I checked out OPGI there's aren't exactly factory. I figured I would come ask the only place there is to ask about a caddy. If anyone out there can. Tell me where to find a new tank or can I get my old fixed. Please me know.

P.s. The hole is… Continue
 
 
 

Photos

  • Add Photos
  • View All

Forum

Burning Rubber

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion 50 seconds ago. 0 Replies

Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light?   Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue

Ordering Polyurethane Replacement Trailing Arm Bushings

Started by Dan McNarry in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 8 hours ago. 2 Replies

There seems to be growing interest in the poly bushings. In order for me to keep track of who wants bushings, please send me a message along with or in lieu of a reply to either this thread or the…Continue

bucket seat covers

Started by Joseph Pagliuca in Wanted to Buy. Last reply by Bobby Brown 10 hours ago. 3 Replies

looking for leather seat covers for bucket seats In a 1964 Cadillac Eldorado convertibleContinue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 10 hours ago. 177 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service