There was some discussion on the 63/64 Cadillac Website regarding how to bleed brakes with a vacuum pump, and needed to bleed the brakes on my '02 Escalade EXT after installing new rotors, calipers and pads, and recorded this short video showing how it is done. It is not a 63 or 64 Cadillac, but it is the same procedure.

Views: 114

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Anders on July 29, 2017 at 8:18am
Comment by Jason Edge on July 29, 2017 at 7:55am

Local Auto stores. I got mine from AutoZone.

Comment by Kim K Kaiser on July 29, 2017 at 1:03am

where would you get a vacuum pump like that??

Comment by Anders on December 23, 2016 at 9:32am

Perfect Jason. Thanks.

Also liked the fact that the camera was mounted on a tripod or similar. Some of your other videos makes me "sea sick" from the moving camera. But this was so much better.

Have bought the very same kit you are using and its on my desk now, awaiting the big job replacing suspension and the steering parts.

Photos

  • Add Photos
  • View All

Forum

Floor Pans

Started by Tommy Nicolosi in Restoration Discussion 11 minutes ago. 0 Replies

Are the floors on 1961-1964 the same???Continue

Back to Starter

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 49 minutes ago. 39 Replies

Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

'63 CDV Restomod on Iron Resurrection on Velocity Channel

Started by Ian Osborne in General Discussion 9 hours ago. 0 Replies

I just watched an episode of a show called Iron Resurrection on Velocity Channel. They did a restomod on a pretty clean survivor '63 CDV for a customer. They did an LS3 swap, air ride, complete…Continue

Blog Posts

HVAC Vacuum Valve Clip-need the one for the Power Control side

Posted by Norman Silverman on September 17, 2018 at 8:15pm 6 Comments

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy…

Continue

7 vacuum valve-need a good one or someone to recondition mine

Posted by Norman Silverman on September 15, 2018 at 5:44pm 12 Comments

So, I've put my 7 vacuum valve from the control head side to the test, and it failed. I looked at the instructions for re-conditioning it and unless I am missing something, the instructions are missing something (about how to take off the clip that provides the tension that holds the two pieces together). 

In any case, I can't do this particular repair so I am looking for a new valve (not likely), or a good re-conditioned one, or someone who has done this before and would do mine for…

Continue

Mosiac Cadillac emblem Table

Posted by Dana G Cooper on August 30, 2018 at 10:48pm 11 Comments

Wanted to share a picture of a table my wife made for me to display with our 63 Coupe Deville. 

Inside door handle thread size

Posted by Michael Jarnagin on August 23, 2018 at 4:31pm 1 Comment

Anyone know the thread size on the inside door handle bolts mine are missing any info much appreciated 

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service