Views: 246

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Kurt on June 18, 2018 at 10:09am

I'm thinking about replacing my A6 compressor with one of these. My A/C cools fine but the A6 has a tendency to sling oil from the shaft seal which makes a mess. Is this Pro6ten compressor really as "drop in" as they say? Same mounting, hoses, etc?

Comment by Eric stolte on June 18, 2018 at 7:43am

Kurt I bought the compressor from OPGI, it works very good.

Comment by Kurt on June 18, 2018 at 12:34am

Hi Eric, what kind of A/C compressor is that?

Comment by Eric stolte on February 24, 2018 at 10:46am

Paul I have the Holley EFI on my Pontiac,  it’s not the sniper  it’s the full system and I like the FI TECH better

Comment by Anders on February 20, 2018 at 5:56pm
Comment by Clovis on February 20, 2018 at 2:14pm

Paul read my thread on my fitech installation. You can also go the their website to see whats available. 

Comment by Paul Gostick on February 20, 2018 at 4:24am

Hi Eric I’m restoring a 63 Fleetwood Sixty Special in New Zealand running a rebuilt 390

My mechanic said I should look at fitting the Holley Sniper EFI system but your one looks good and by the reviews seems to perform well too and cheaper than the Holley.Is that the standard Cadillac manifold and can you give me tips on what linkages I need and what’s the canister model?

appreciate the advice not many 63 Caddy experts in New Zealand!

cheers Paul

Comment by Clovis on November 2, 2017 at 1:19am
I don't think it's the best idea to drill into a head and tap it. If you look in my thread about emissions you can see the inline rad hose adapter I use for the thermally ativates vacuum switch. It came with a 1/4" hole but I drilled and tapped it for 3/8" pipe. Just a few buck on Amazon.
Comment by Michael Forte on November 1, 2017 at 11:20pm

Thanks Eric.  I want my factory gauge to work so I'll have to find another place for that sensor.

Clovis, I asked the question because I had been looking around my engine for a spare plugged off factory hole and wondered if Eric found one.  Looks like Cadillac only gave us one tapped coolant passage and used it for the dash gauge.  After I convert and the car is tuned, I'll be unplugging the handheld computer and using the factory gauge, so I'll need to make another hole.  I'll probably either tee off the hose fitting on the back of the crossover tube or drill and tap a new hole on the opposite cylinder head.

Anyway, yeah, this isn't my first.  I do all my own work except bodywork and upholstery.  I've converted several cars to EFI but this is my first Cadillac.  I'll have mine completely apart as well for a complete under-hood restoration.  No worries, just planning my attack!  LOL.

I'll check out your posts, thanks!

Comment by Clovis on November 1, 2017 at 10:53pm
Micheal are you a hands on guy when it comes to your car? Have you ever done major work such as this? I ask these questions because this is not a simple installation. Tuning it is also not so simple either. If you've done this before jump right in with both feet as it's very rewarding.
Your questions about the temperature sending unit tells me this may be a bigger project, automotive wise, than you've ever tackled before. I highly suggest you find a reputable shop that has done at least two of these installs before. I eat sleep and live for this kind of stuff all my life so I didn't even bat an eye when it came time to do it. Since everything was apart I also detailed the engine compartment and totally went through the comfort control system. I also rewired and added electric fans. This was done simultaneously with the efi install.
If you are thinking about doing it still read my posts, there are several, on the efi and comfort control installs. Happy building sir.

Photos

  • Add Photos
  • View All

Forum

off the wall question

Started by James Fejerang in 1963/64 Cadillac Specific Discussion. Last reply by Ray Schick 8 minutes ago. 1 Reply

 Could anyone please tell me why on some models of the 64 devilles, the Bezel, Turn signal (LH upper) is clear and the other one RH Bezel is chrome.  Sorry if this is a stupid question, but i have…Continue

fuel pump

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Anders 2 hours ago. 4 Replies

I am gathering up some stuff to put away for the potential trip home in oct/nov from MT to MS in the 63 cdv.i thought a fuel pump may be a good piece to have nearby,  Are the newer ones like you can…Continue

rear seat speaker grill

Started by Kenneth R Hudgins in 1963/64 Cadillac Specific Discussion 11 hours ago. 0 Replies

Looking for a rear seat speaker grill for my 63 EldoradoContinue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 159 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service