I have a brand new Edelbrock 1406 carburetor the I would like to install on my 63. I have used these carbs on several vehicles that I have owned (Fords) and they work very well straight from the box. My concern is connecting the TV rod to my Jetaway tranny. Is there a way to mate the TV rod bracket from my AFB to the Edelbrock carb or do I need to get creative? I spent some serious dollars to have my tranny rebuilt and would hate to screw it up over a simple carb swap. Thanks

Views: 5444

Reply to This

Replies to This Discussion

Just fabricate a bracket to mount the TV rod to the throttle plate.  The geometry is important, as the Throttle plate needs to pull the TV rod during the entire throttle range.  Notice that the stock setup has the TV rod hooked up below the pivot point of the throttle plate.

The attached picture shows the path of travel for the TV rod during acceleration. At max throttle, the TV rod is still in the green, and not arcing back towards the tranny.   Once the TV rod starts to arc into the red, it is going back towards the tranny, and that is bad, as the engine is accelerating, and the trans thinks it is decelerating.

Its actually an easy mod, just measure the distance of how far the TV rod is forward and below the pivot point of the throttle plate on the stock setup. Mount a plate to the Edelbrock throttle plate and see where the TV rod hook up post sits in reference.  Just gently push the TV rod back to the trans and see where the post aligns up.  Drill a hole in the plate, weld a few washers to the plate so the post doesn't wobble.

 My main concern has always been maintaining the proper travel of the TV rod. Thanks for the info Russ. 

As I just put an Edelbrock 1406 on my 1959 390, wanted to share a picture of a transmission rod bracket made by a friend in my CLC region.  Echoing advice by Russ - on the old carb, from the throttle linkage mounting hole, measure how far forward and down the trans rod mounted, that should be where to drill the hole in your custom bracket, assuming the arch when the throttle is opened is as shown in green.

That is by far the best setup I have seen. I never thought to use pop rivets, great idea.

Can you see if your friend will make more of those brackets for me?

That is too cool! I am with Russ, I would love to buy two of those as well. Your friend has created the perfect solution for our carb swap. Thanks Mike.

I would buy one if it comes available. Please keep me in mind. Thanks

Hello, here is what I end up with for attaching the transmission kick down rod to an Edelbrock carb.  First, to make a custom bracket, I looked at the original Rochester 4GC off the car and measured the distance between the stock throttle and trans rod mounting points, and the arc that the trans rod travels from idle to wide open throttle.  Then I realized "That bracket can be removed.  I wonder if..."

Below is the Rochester bracket removed.  I rotated the bracket approx 90 degrees to the left from it's original position, and aligned the now top hole in the bracket to an existing hole in the carb bracket, under the large hole.  Now the stars aligned, because a hole in the bracket that previously had a screw in it (above bottom right) aligned with the throttle rod mounting hole on the car.  I did need to enlarge the hole in the bracket to accept the throttle rod.  Up at the top of the bracket, I attach with a bolt/machine screw that has a somewhat thin head to make sure it didn't interfere with the idle screw.

With bracket attached to the carb, I put the trans kick down rod in the conveniently located stock mounting hole.  This was going too easy.  Yep, the trans rod was too low and hanging up down where the engine block meets the trans.  Not done yet.

So I measured how far up the trans rod needed to be in order to have clearance as it moved forward and up as the throttle went to WOT.  I drilled a hole in the Rochester bracket just above the original trans rod hole, where the trans rod travel would have the max arc up and forward without any interference.  The nut on the trans rod is just to take up some space.

Then it was just a few test drives to adjust the mounting position of the trans rod.  It works great!  Get on it and the car downshifts and takes off way stronger than it ever has since I've owned it.  And it was free! (the bracket).

How did a guy with a 59 ended up on this great 63/64 Cadillac site?  Here's my 64 Coupe de Ville.

Hey Mike, do you have access to another fabricated bracket shown in your picture? I want to install an Edelbrock 1906 carb to my 390 and am having a tough time finding bracket. 

Aaron

any idea what the replacement jet size would be? i was actually looking into upgrading my metering rods to help richen the mixture. 

Tuning a carb requires extensive experience and the understanding of how a specific carburetor works.

This will be your best friend if you do not have that extensive knowledge.   I even have the bungs welded into my cars.  Bought 1 unit, and plug the bung when finished tuning the carb.

https://www.summitracing.com/parts/edl-6593?seid=srese1&cm_mmc=...

Ive been reading alot about how it works, and how it effects the car. The posses seems pretty simple, even if you went at it with the classic trail and error style. If only the full range tuneing kit wasnt 90 bucks lol

What are advantages to going to thrse more modern cardureators,  what do you accomplish vs the rochester inhave on my car.  Im not touching mi e, as i think car is running just fine,  just curiuos to the reason

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith yesterday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service