The Carter AFB and Rochester 4GC were used on the 1963 & 1964 Cadillacs. There was not specific body style, or setup you would see one or the other used and will find either on any particular Cadillac. There were specific model #'s and differences and have posted information I have collected over the years. This might not be complete, but includes the notes I have on file and welcome any updates.

According to the 1964 to 1969 Master Parts book page 219,  The 1964 Carter AFB replacement carb was the 3903S.  The 1959 to 1963 Carter AFB was the 3480S.  The difference between the 3480S and the 3903S is the 3903S has a mounting block on the left/driver side rear with scew holes to hold the electric kick down switch used on the TH equipped cars.  I have seen the 3480's continued to be used on the 1964's that did not require the switch (62 series and 75 series and commercial chassis that had the older Hydrmatics).

Now what was put on these cars later as they were serviced is a smorgasborg.  I have on hand 3904S, and a couple of SR3656S,...but no 3955S.  If you have an new master parts list it probably shows one of the newer carbs.  This was very common.  For example the 1963 Lo and Hi note horns were larger than the 64 horns, but the 64-69 Master Parts book calls for the 64 style as the replacement for the 63 because they no longer made the 63 style.

  

Here is a listing of the Carbs I have that were originally used for 1963 & 1964:

1 963 8 390 Carter AFB 3480S 577  (without AC)
1963 8 390 Carter AFB 3481S 577  (with AC)
1963 8 390 Rochester 4-GC 7023030 1122
1963 8 390 Rochester 4-GC 7023031 1122
1964 8 429 Carter AFB 3655S 577  (without AC, used as service replacement carb through 1967) 
1964 8 429 Carter AFB *3656S “AD4” 577 (with AC)
1964 8 429 Rochester 4-GC 7024030 1305
1964 8 429 Rochester 4-GC 7024031 1305

Additional Notes added July 3, 2016

For 1963 the Carter AFB's for cars without AC were 3480S
For 1963 the Carter AFB's for cars with AC were 3481S
The Service (replacement) carb was the 3680S ... at least until sometime in 1967 when the 3903s became the service carb.

For 1964 the Carter AFB's for cars without AC were 3655S
For 1964 the Carter AFB's for cars with AC were 3656S
The Service (replacement) carb was the 3655S

CFM Ratings:

CFM ratings were not listed in the Shop Manuals or Dealer Data Books and Carter was really vague in terms of the Carter AFB which could range from 400 cfm up to 900 cfm from what I have read. 

Rochester 4GC is a bit easier as they only made 3 CFM's during this time period: a 486, 553, and 692 cfm carb. You can compare the venturi and main bore diameters (1 1/8 1 15/32 / 1 7/16 1 11/16) to quickly lock in on the fact it was a 553 CFM carb. Since the specs for 63 and 64 are the same you pretty much assume the carbs are the same CFM rating.

As far as the Carter AFB, I had done some research that let me to believe their carb was a 575cfm. There were tons of model # but looking at later ones with CFM rating seemed to narrow it down to 500 CFM to 575 CFM, with the 575 CFM being the closer rating.

Example Pictures:

Carter AFB Carb:

Gaskets & Shim Installation:
--> for Rochester 4GC it is intake, gasket, insulator, gasket,  carb.
--> for Carter AFB it is intake, gasket, insulator, gasket, shim, carb.
Here are the installation instructions you will find in the shop manual in the Carburetor Removal and Installation section (page 10-11, section 20.b. in 1963 manual; page 8-17, Section 27.b. in 1964 manual). 

Rochester 4GC Pictures:

Misc Pictures:

Here are a couple of pictures showing the 1964 Carter AFB with the Kickdown Switch for theTurbo Hydramatic equipped body styles:


Here is the top and bottom of the Intake to Carburetor Insulator:
 

Views: 20259

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Norman Silverman on January 10, 2019 at 9:17pm

Just sent you an email. Happy to purchase them from you!

Comment by Norman Silverman on January 10, 2019 at 9:11pm

Much obliged !

Comment by Jason Edge on January 10, 2019 at 8:22pm

For the Carter AFB I sell the Fel Pro 60034. It takes 2 of these gaskets, one below and one above the insulator. (For Rochester carbs, use the Fel-Pro 9770). I have been selling both new for many years for $5 each. If you have trouble finding a gasket and want one of mine email me at jasonedge@nc.rr.com.

Here is a picture of the FelPro gasket I sell for the Carters:


Here is the Fel Pro 9770 for the Rochester 4GC:

Comment by Norman Silverman on January 10, 2019 at 8:00pm

Need to know which carburetor manifold gaskets to buy. I am replacing my original 3656S carburetor with another (rebuilt) 3656S carburetor. Do I buy the ones that are a match to the spacer shown here, or do I buy the old kind that have just the four barrel holes in them?

Thanks 

Comment by Bill Bunch on June 25, 2016 at 10:07am

Thanks for that advice.  I'll definitely check the plugs.  Something is definitely out of whack.  It uses a gallon of fuel just getting to the end of the driveway.  It was always a bit thirsty, but not that bad.

Comment by Bill Bunch on June 23, 2016 at 4:07pm

My 64 Series 62 has been "upgraded" to the Edlebrock 1406 by my mechanic.  It runs great but the air cleaner housing no longer fits because the 1406 has a wider mouth than did the original carburetor.  I see carburetor rings sold by some manufacturers but they seem to just elevate the air filter housing.  I see none that adapt from the larger ring of the carb to the smaller air cleaner housing.  How have others handled this difference?  I really don't want to do with an aftermarket air cleaner.  I'm trying to stay as close to stock as possible.

Comment by john chalk on July 4, 2013 at 3:43am

just have the manifold off my car to replace a blown intake gasket.  did not take enough notice when the carby came off - it is a carter - so when I refit - confirm - Manifold - Gasket - Bakelite spacer - Gasket - Shim - Carby ! cheers

Comment by Jason Edge on October 19, 2012 at 10:54am

Just added a few pictures to go along with this post.

Comment by Jason Edge on August 17, 2012 at 5:02pm

No...just the fuel supply line from fuel filter to the carb. The are similar because it is my understanding that Carter sold Edelbrock the Patent for the AFB design..or perhaps all of there designs.  Looking at the Carter AFB and Edelbrocks side by side they are very similar in shape and layout..from the metering jets down to the fuel inlet and the throttle linkage.

Comment by Jason Edge on August 17, 2012 at 3:20pm

I would say about 1/2 and 1/2 on the 38 parts cars and 4 or 5 driver cars I've had. They get mentioned more I think because they design is very similar to the Edelbrock Performer 1406 and 1411 which many people go with if they are switching to an aftermarket carb.

I've probably got more Rochester 4GC cores on hand right now than Carter's in my parts bin.

Jason.

 

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith yesterday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service