Hi everyone - I am working on my 64 Fleetwood and recently pulled the front cover to do the timing gear and also replaced the timing seal with a new one while I had the cover off.
While I was at it I also decided to install a repair sleeve for the harmonic balancer since I figured it was worn down on my 110k engine. The sleeve went on pretty easily with some light taps from a hammer.
Today I began reassembly, using a harmonic balancer installation tool to make sure it went on easily. While i slowly screwed the balancer in place, it appears the lip of the new shaft seal caught an edge and a small section started to bend in. I stopped, removed the balancer, and am now waiting for a new seal to come in tomorrow. Before I do the same thing again...has anyone experienced this before? It seems to me this was either a one time fluke (caught a random edge), or the shaft is slightly off center to the bearing, and the repair sleeve exaggerate the problem, or perhaps the repair sleeve made the harmonic balancer shaft too large? I can’t find specs in the FSM on proper shaft size.
Thoughts?
Tags:
Just bad luck is all. Be sure the sleeve is flush all the way around.
I assume you lubed the seal & sleeve with oil, correct?
It's possible that the seal started catching on the sleeve. Hopefully just an isolated incident but more oil couldn't hurt.
Thanks everyone for the suggestions. Got a new seal today and put a ton of grease on the seal and shaft. Went in without any problems!
Started by Scott Santora in General Discussion. Last reply by Dennis P. DiBari 9 hours ago. 4 Replies 0 Likes
I could use some confirmation. I sent out my radiator for my 63 De Ville to get re-cored. Several weeks later, when I went to pick it up from the service vendor, I noticed a large amount of green…Continue
Started by Jason Edge in Trivia. Last reply by Cees de Bunje 18 hours ago. 13 Replies 0 Likes
It has been a while since we did some trivia and I was watching a movie last night and saw this 1964 Coupe de Ville that briefly makes an appearance. The Trivia Question is: What Movie Is this?…Continue
Started by Todd Fox in Restoration Discussion. Last reply by Todd Fox yesterday. 2 Replies 0 Likes
Has anybody in here found a good supplier of replacement floor braces for the 64 convertibles. Continue
Started by Jason Edge in For Sale yesterday. 0 Replies 0 Likes
I just pulled a very good Cadillac Cylinder Head Water Outlet Pipe for cars with AC with the extended arm for compressor. That came off a running parts and is a nice piece. Included is a new 180…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
ContinueApril 21, 2024 from 8pm to 9:30pm – Zoom
0 Comments 1 Like© 2024 Created by Jason Edge. Powered by