i got call about engine after review.
He told me i required 30 over pistons ring.
Standard main bearings. He only had to polish the crankshaft.
My question is if the hole is bigger now. Woukd that affect compression. He suggested just standard as he felt it would be minimal at best.
Any thoughts on that.
Tags:
Standard bore x stroke for a 390 is 4 x 3.875.
Overbore of .030 gives you 4.030 x 3.875.
Radius of cyl is now 2.015. r^2 = 4.060225.
Pi = 3.14
3.14 x 4.060225 = 12.7491065 (Area of circle formed by the bore)
multiply that by the stroke 12.7491065 x 3.875 = 49.4027877 = cu in per cyl, x 8 = 395.222302
Your engine is now 395.222302 cubic inches, or rounded down to 395.
So no need to have any concerns regarding camshaft?
Cubic Inch Displacement will increase a bit (Bill Conte has done the math for you), and compression may slightly alter from the stock 10.5 to 1 compression with the new standard pistons ... but marginally at best and absolutely nothing to worry about. The aftermarket pistons are most likely designed to dial on to the stock compression ration given bore and stroke, unless you could even find low or high compression pistons. There were low compression options for these engines back in the day but have not looked to see if you could even order these if you wanted to.
Marvelous arithmetic by Mr. Conte! I'm glad someone remembers all that stuff they learned in school, I lost it all within a year or two.
This is one engine I wouldn't worry about boring larger holes in - the new block was rolled out in '63 with plenty of extra room for that; GM knew they were going to be boring it out further and further over the next 5-10 years to accommodate more accessories and performance demands. This basic same block ultimately wound up at 500 cvi before the oil embargo prompted the government to force manufacturers to forget looks and power, in favor of economy.
Started by Mack in 1963/64 Cadillac Specific Discussion on Tuesday. 0 Replies 0 Likes
Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue
Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith on Tuesday. 1 Reply 0 Likes
I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue
Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies 0 Likes
I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies 0 Likes
In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by