Jim Long's Events (1)

June 22Wednesday

RSS

Jim Long's Event Types

August 2021
SMTWTFS
1234567
891011121314
15161718192021
22232425262728
293031
       
September 2021
SMTWTFS
1234
567891011
12131415161718
19202122232425
2627282930
       

Photos

  • Add Photos
  • View All

Forum

Factory AC clutch fan needed

Started by Chris Gill in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 1 Reply

Hi folks,My clutch fan died so I desperately need a new one. Unfortunately it will take a week or more to order from the usual suppliers so I am hoping someone on here has a manufacturer name and…Continue

Replacing Front Door Window Chrome Channel

Started by Michael Vogler in General Discussion. Last reply by Tony and Ginny 429 5 hours ago. 1 Reply

List Mates,My '64 De Ville Conv. front door window chrome trim needs to be replaced.  The chrome on both front door window his getting a little bit of pealing off.  I have the chrome replacement…Continue

Vacuum advance

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 1 Reply

Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue

1963-1964 Convertible Parts

Started by Charles Fares in For Sale yesterday. 0 Replies

1963-64 Convertible top switch with chrome bezel and mounting retainer clip, tested and working, nice chrome, $65. 1963-64 Convertible rubber A-pillar seals LH and RH pair (repops) $50 the pair.…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service