David Thomas's Discussions (138)

Discussions Replied To (135) Replies Latest Activity

"Some parts house sending units are not properly calabrated. Lectric limited  has the…"

David Thomas replied Jun 20, 2016 to Temperature gauge

6 Jun 20, 2016
Reply by Kyle garner

"Did you check the shoes fit to the drum before you installed them? If they don't fi…"

David Thomas replied Jun 19, 2016 to problem with new brakeshoes

15 Jul 15, 2016
Reply by john vanttinen

"Glen, congratulations on your new Cadillac. I would replace the master cylinder or r…"

David Thomas replied Jun 13, 2016 to Power assist brakes issue

21 Jun 19, 2016
Reply by Tony and Ginny 429

"Looks good Jason. Interesting, for 64 Cadillac did them under hood black. On my 63,…"

David Thomas replied May 26, 2016 to Small Under Hood Color Correction Project Today

12 Jun 7, 2016
Reply by Denny Link

"You might try  Egge machine or Terrell machine for parts. Tried Rockauto or NAPA?"

David Thomas replied Apr 27, 2016 to Camshaft Info Please

5 Apr 27, 2016
Reply by David Thomas

"You could buy some thin gasket material and make your own. Or buy the front cover se…"

David Thomas replied Mar 26, 2016 to Gaskets

3 Mar 28, 2016
Reply by DUANE ROBINSON

"Hi Greg, as long as you are going to disassemble the drive shaft to install the new…"

David Thomas replied Mar 10, 2016 to 1963 Drive Shaft

3 Mar 10, 2016
Reply by David Thomas

"Cody, If the starter is turning slow after warm up, you may have a dragging starter…"

David Thomas replied Mar 9, 2016 to Initial start problems! HELP

17 Mar 22, 2016
Reply by Russ Austin

"I know you have a 64 with the TH400, but, I have changed the tail shaft housing bush…"

David Thomas replied Feb 6, 2016 to heart beat in my steering wheel.

22 Feb 6, 2016
Reply by David Thomas

"Clovis, I know the 63 and 64 A/C are two different animals. Over 20 years back, I sw…"

David Thomas replied Sep 13, 2015 to Climate control throttling valve upgrade

11 Sep 15, 2015
Reply by Clovis

RSS

Photos

  • Add Photos
  • View All

Forum

Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd 7 hours ago. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 14 hours ago. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion 14 hours ago. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 yesterday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Events

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service