Anders's Discussions (1,161)

Discussions Replied To (1082) Replies Latest Activity

"I didn't say that any prior lung damage would help get past Covid. I said that there…"

Anders replied Mar 13 to I installed a Stereo System in my 64 Coupe de Ville Dino Today

8 Mar 13
Reply by Anders

"Don't think you would get any vibration from that. But not sure what part you are re…"

Anders replied Mar 13 to Transmission tail shaft bushing (s) and seal for 64 with TH400

18 Apr 2
Reply by Norman Silverman

"Yeah Ian. Only three people can light up at the same time. That is really a big prob…"

Anders replied Mar 10 to I installed a Stereo System in my 64 Coupe de Ville Dino Today

8 Mar 13
Reply by Anders

"Hmm, my sender was completely rusted away. The filter in the bottom of the fuel tank…"

Anders replied Mar 10 to Gas Gauge Goes to Half Full

6 Mar 10
Reply by Lee Martin

"Imagine doing a full EV-conversion. These cars would be perfect. A good sturdy frame…"

Anders replied Jan 7 to 1964 cadillac engine

5 Jan 8
Reply by Tony and Ginny 429

"Sold for 24 000 USD."

Anders replied Dec 23, 2020 to No Reserve Auction on Chapter Member Jim Verraster's 1964 Cadillac Fleetwood 75 Auction

1 Dec 23, 2020
Reply by Anders

"From the 1964 Cadillac Shop Manual: "

Anders replied Dec 19, 2020 to oil pressure, again,

2 Dec 19, 2020
Reply by Anders

"Been in contact with TA-motors. These fuel filter are genuine NOS. So these are 55+…"

Anders replied Dec 14, 2020 to Aftermarket fuel filter with return line for '63?

28 Dec 14, 2020
Reply by Jason Edge

"The filter always needs a gasket. Even if Wix claims it doesn't need one. IT DOES an…"

Anders replied Dec 12, 2020 to Aftermarket fuel filter with return line for '63?

28 Dec 14, 2020
Reply by Jason Edge

"If you want replace your springs maybe you should contact Kanter instead. I bought a…"

Anders replied Nov 30, 2020 to do I need new springs?

16 Dec 1, 2020
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Happy Father's Day!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 15 hours ago. 1 Reply

Happy Father's Day to my dad, Sam Edge. He was there in the beginning with…Continue

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 7 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 on Saturday. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service