Kevin Campbell's Discussions (1,495)

Discussions Replied To (1366) Replies Latest Activity

"Geez, I really wish we'd come over 2 years ago when we had planned to. Some idiot, i…"

Kevin Campbell replied Sep 22, 2020 to Edelbrock 1406 Carburetor + Parts For Conversion For Sale

17 Feb 27
Reply by Ian Osborne

"Congratulations on the sale Ian."

Kevin Campbell replied Sep 21, 2020 to Edelbrock 1406 Carburetor + Parts For Conversion For Sale

17 Feb 27
Reply by Ian Osborne

"ha ha ha .... trust you to stick ya head in. LOL"

Kevin Campbell replied Sep 18, 2020 to AC update

11 Sep 18, 2020
Reply by Kevin Campbell

"Ha ha ha.... I thought you were up to speed with the Aussie humour at putting shit o…"

Kevin Campbell replied Sep 17, 2020 to AC update

11 Sep 18, 2020
Reply by Kevin Campbell

"Only joking Joe..... t'was only joking. I'm a fairly large bloke, the fan was a righ…"

Kevin Campbell replied Sep 17, 2020 to AC update

11 Sep 18, 2020
Reply by Kevin Campbell

"I had my fan motor out a couple of years back. (bit awkward to do huh Joe) I had a r…"

Kevin Campbell replied Sep 17, 2020 to AC update

11 Sep 18, 2020
Reply by Kevin Campbell

"Jason....YOU VERY FUNNY MAN..... :-) You fixed that dicky ticker lifter yet.... hmmm…"

Kevin Campbell replied Sep 8, 2020 to AC Center vent update

20 Sep 12, 2020
Reply by Joe DiIaconi

"With the Air Cond running Joe. Its a bit like an low pressure area around the quarte…"

Kevin Campbell replied Sep 5, 2020 to AC Center vent update

20 Sep 12, 2020
Reply by Joe DiIaconi

"Hey Joe, on a really hot day, if i'm after some extra circulation, I flip the rear q…"

Kevin Campbell replied Sep 5, 2020 to AC Center vent update

20 Sep 12, 2020
Reply by Joe DiIaconi

"OH, make sure you have no loose clothing on and be friggin careful around the tailsh…"

Kevin Campbell replied Aug 16, 2020 to 64 SDV axle bearings

16 Aug 16, 2020
Reply by Chris Cheveau

RSS

Photos

  • Add Photos
  • View All

Forum

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Phil 9 hours ago. 18 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by Jason Edge 9 hours ago. 8 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 9 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 20 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service