Hi the  390 motor in my 1963 Coupe is toast and can not be repaired. I am in need of either a complete motor or small block or big block any block. I have tried most of the advertised parts dealers on the site but no luck. Any help in finding one would be greatly appreciated. 

Views: 182

Reply to This

Replies to This Discussion

The parts you are looking for —may be available right here when the boys come by 

Enjoy 

Not sure what you mean by when the boys come by in  your reply. Thanks.

He's referring to Jason and Russ.

You must've done a number on the 390 for it to be unrepairable. Did it throw a leg out of bed?

I bought the car as is knowing that there was a problem with the motor. When I tore it apart,  I found out that a piston had disintegrated and the connected rod when through the cylinder leaving a two inches hole. Now I have to replace it or rebuild one with the good parts that are left.

Holes in the block, geez, some bondo and chemi weld and you're going again. LOL

Since I reside in Eastern Canada I was thinking more likes duck tape or hockey tape LMAO. But I do have my work cut out. It's a long winter here so I have time on my hand to get the motor ready for spring.

Hehe, "duck tape" is a bit funny. However where I live its called "Strömma tape". Strömma is a large passenger vessel company and, according to the rumour, they are famous for repairing everything on their boats with the gray sticky tape originally named duct tape.

Picture of Strömmas Östanå in a wintry Stockholm archipelago:

Btw Kevin, when you get here an archipelago cruise is on the schedule. However not with Strömma. We will take a steam boat cruise on Storskär eating steam boat steak.

For those that doesn't know, steam boat steak is a tender piece of meat that is put on the coal shovel and into the furnace of the boiler for a few seconds. Tastes a bit weird and sooty. Well worth it for a motor head.

I have bare blocks, short and long blocks.   My email is  russ85747@hotmail.com    Located in Tucson AZ

Hi Russ. We have communicated already by e-mail on Sunday. I will send you another reply by e-mail and see if we can work something out. 

 Marcel

I am sure you now understand what  I meant  by the boys stopping by as we have the regular crew that lives here and drop in very often to help others out with parts and hands on advice 

Do acquire any parts you may be needing from Russ as he has been doing great business since I am on this site as a consultant  ( 3-4 times ) daily since 2006 

Anything Jason can do for you will be golden as well 

These guy live and breath our year cars with the knowledge to get you the correct item at the right price 

Enjoy 

Thanks I will get in touch with Russ.

RSS

Photos

  • Add Photos
  • View All

Forum

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion 4 hours ago. 0 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Valve stem seals for 429?

Started by Matti Roth in Restoration Discussion. Last reply by Matti Roth on Friday. 7 Replies

Hello!I am rebuilding 429 for 64 DeVille and got Felpro head gasket kit including valve stem seals. Is it recommended to install those even though they are not originally used? O-rings will be…Continue

Blog Posts

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 6 Comments

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service