has anyone added a rear sway bar to a 63 convertable 

if so what parts did you use and what source 

Views: 127

Reply to This

Replies to This Discussion

If you have the kind of rear end movement at the rear of the car that you are looking for a sway bar you have other issues to address with your rear end suspension 

There is no rear end sway bar that I know of for our year cars only  the front 

you have a rear end ball joint - trailing arm busing —rear springs and shock that could need replacement 

The rear end of our cars should have no movement ( sway ) at all when all the rear end parts are  working correctly 

The replacement rear end trailing arm bushings available  from all suppliers for our cars are not good and short lived 

There are after market arms being made with with bushings that hold up to repair the rear control arms ( your best solution for that problem ) 

The info about the rear  bushings is on this site 

 the car tracks nicely down the road i am replacing the bushings and springs  front and back,  just notice some peaple have added a rear sway bar to the back and how it improved corning

any info on  after market trailing arms would be great

Never saw a rear sway bar on any 63 or 64 Cadillac 

Enjoy 

Finding the info on the guy making the —aftermarket  replacement rear control arms and bushing —for you 

I will be posting the info shortly 

Enjoy 

Brian 

You want to contact  Dan at dmcnarry@telus.net   who is making custom rear control arms with poly bushing for our year Cadillacs

At the present time the only good solution available for rear control arms that will hold up as they should 

The arms have been installed and tested here and do the job intended 

You need to address the yoke ball joint above the rear axel to be sure it is in good working order 

Those  rear end supports will keep your rear end gear case in the location it was intended to be in relation to the drive shaft during acceleration and deceleration

Enjoy 

Tony

thank you for the info

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 10 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 12 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 18 hours ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service