1964 DeVille front lower bumper end (bucket) passenger side

Hey all ,

Looking for a lower front bumper end for the passenger side of my 64 DeVille. It has taken a while but I now have everything except that piece.. it does not have to be new chrome or even have nice old chrome. Just need it not rusted and rotted out.. any help would be great,. Thanks

Views: 114

Reply to This

Replies to This Discussion


One of a few items that has been a bit difficult to be finding the last few years 

Been a while since we have seen any  for sale on this site or anyplace else 

Just a heads up on that 

Good  luck  in your searching 


Yea I have realized this since I started looking, I have only found a few and the ones I have found are either mint condition for 700-1000 or they are pretty far gone

Jeremy,  Is this what you are looking for?  

Sorry I'm not sure what your talking about there is no link or pic

OK the discussion post is not doing what I want it to do  Send me your email address and I'll send the picture that way  I am at - pat.westphal@gmail.com


The pic is there but as an attachment. I have attached as an image here.


There is a button to attach images directly to the post.


Thanks for the help.  As usual, ignorance (mine in this case) is bliss.  

Yes the passenger side lower bucket.... In the pic it is sitting on top of eyebrow
I was wrong, in the pic the one on the eye brow looks to be driver's side, I need the one on the other side sitting between the headlight trim and eyebrow

Just saw two  64 lower bumper buckets on eBay 

Was 750 re- chromed  and the other new for 600 

New has a superior chroming process back in the day 

They were often found in the past for 300 - 400 but they are getting harder to find these days 


Thank you.. I may have seen those but I will definitely check it out.. thanks alot



  • Add Photos
  • View All


Timelapse Rebuild of a 1957 Cadillac 365 V-8 Engine

Started by Jason Edge in General Discussion. Last reply by Kurt 2 minutes ago. 1 Reply

Saw the link on the CLC forums today and thought I would share to the CLC FB Group. This is a prior generation engine to our 1963-64 390's & 429's but this is a pretty cool time lapse of a…Continue

64 TH400 refresh

Started by Matti Roth in Restoration Discussion. Last reply by Matti Roth 2 hours ago. 8 Replies

 Next task with my 64 DeVille project is to check TH400 condition. Gearbox came with the car but was already removed. It is 64 but not possible to say if it is the original to this car as there is no…Continue

need some help: bulb size for dash compartment

Started by Stefan in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 4 Replies

Hello everybody,I would like to replace all the burned bulbs in the dash of my ´63 Fleetwood 60 Special and I'm a little confused as I can't find the right sizes in the shop manual. - If I'm wrong,…Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 299 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

bright beam flashes

Posted by Kim K Kaiser on January 9, 2022 at 12:55pm 5 Comments

HI again,

I have the 63 cdv, with the flash assister on the dash,  

My hi lo beams flash back and forth intermittently.  sometimes they dont start flashing at all, sometimes they will just start flasihing on and off until I hit the button on the floor to get them to stop.  sometimes they sound someone is down there hitting the floor button but the lights dont respond, you can hear the click but nothing happens, as if I have no control over that floor button. I have turned off…


Map Light

Posted by RIchard Yasenchack on January 1, 2022 at 8:07pm 7 Comments

I have a 63 Cadillac Series 62 convertible.  Can someone post a picture showing what the map light should look like?

Mine is a meta air vent like grating, which just does not look right for a map light.

Thanks in advance.  Rick

Upgrades for the Coupe de Ville

Posted by Kurt on December 24, 2021 at 6:00pm 4 Comments

At long last I finally have power vent windows! I started collecting the parts 3 years ago. The one thing I could not find until recently is the 6 button driver's switch. Jason finally pulled one in and was more than generous with pricing. Thanks Jason! Installing the vent window motors was the easiest part of the project but many other tasks were spawned by this project.

  1. There is a hole in the door panels where the window crank was. I considered putting a hub cap emblem there…

center bolt size for crankshaft pulley

Posted by Dan Norris on December 6, 2021 at 3:13pm 2 Comments

I need to pull my distributor, and still have the cork in the end of the crankshaft. What is the bolt size needed to thread a bolt in there to be able to turn the motor over with a pull handle and socket to get it to TDC exactly before I pull the distributor out?



  • Add Videos
  • View All

© 2022   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service