I'm putting  front bumper together and I don't know where 2 pieces from the picture should go.

Please let me know ,thank you,

Paul

Views: 68

Attachments:

Reply to This

Replies to This Discussion

Thais the nut plate bar and shim for the upper end impact bar to upper center impact bar.  The nut plate bar goes on the center impact bar side and the bolts go in through the end impact bar side. It keeps the 2 pieces together.

The shim goes in between the 2 pieces, end and center impact bar.

Is this the right place in the picture?And the shim placement has to be specific way?

Thank you,

Paul

Attachments:

Paul, Your orientation is correct, just as Russ pointed out: "The nut plate bar goes on the center impact bar side and the bolts go in through the end impact bar side."  The shim is sandwiched between the 2 pieces. Shim goes on with long tab to rear.

Thank you very much.

Paul

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 minutes ago. 40 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

need parts to rebuilt hydramatic transmission gearbox.

Started by Tanguy J. ROSEZ in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon 2 hours ago. 1 Reply

Hello everybody, I am from France, and I need to rebuilt the HydraMatic transmission on my 1963 PND2D1LR. Could you give me some good Professional adresses in US to buy the parts ?Continue

Henry Leland- founder of Cadillac and Lincoln

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 20 hours ago. 1 Reply

Here's a good article about Henry Leland. I had heard bits & pieces of his story over the years but didn't know all these details.…Continue

1963 Cadillac Convertible Door Jamb Switch

Started by Lee Martin in 1963/64 Cadillac Specific Discussion. Last reply by Lee Martin on Friday. 3 Replies

Okay, it's "dumb question time!"  Here's mine:  Does anyone know the part number for the 63 convertible door jamb switch (3 prong)?  I cannot find this in the manual...thanks!Continue

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service