My car is gone so I have no need for the extra parts I have lying around. I will charge only actual shipping to be determined by buyer's address.

More photos of anything available by request. prices are negotiable.

Email me at ozzie90249@yahoo.com 

1963 Side Light Bezels - They have been recently re-chromed but it was a quick job and pitting was not filled. Chrome shines but far from a show piece - $75/pair

1963 Tilt Wheel Gear Selector and Tilt Knob Good Chrome - $35 for both

Dash Piece below instrument bezel for tilt steering column - $30

Views: 196

Reply to This

Replies to This Discussion

Driver Side Boomerang #1 - Good chrome but there is a crack around the inboard mounting stud $60

Driver Side Boomerang #2 - Has dings and not great chrome but these are not easy to come by - $30

Glove Box Door - Has button and lock but no key. No script either - $25

Original 1963 Shop manual - Very clean and solid binding - $35

Both boomerangs are 1963 model year.

Boomerang #1 has been sold

Shop manual is sold

More small stuff

63/64 convertible rear quarter light housings with lenses, light pitting - $75

Pair convertible rear quarter lenses - with cracks but still one piece - $35

Ashtrays - $10 each

Odometer reset cables - $10 each

Wiper/washer switch, I believe this is 1964 style but will fit '63 - $25

Vent window regulators with cranks - $40 pair

Rear view mirror/sun visor bracket from '63 CDV, very light pitting, should polish up nice - $25

Pair'63 fender indicator gun sights, typical light pitting - $40 pair

Original seatbelt from'63 convertible, has Cadillac/Hamill patch sewn on, with mounting bolts. This is 57 years old so the webbing should be replaced for safety - $50

Convertible rear quarter lenses sold

RSS

Photos

  • Add Photos
  • View All

Forum

Neutral Switch issues

Started by Rob Shatsnider in Restoration Discussion. Last reply by Mark S Anderson 2 minutes ago. 1 Reply

On a 1964 60 Special with a tilt wheel, tubro trans and #653 neutral switch.  When I had the transmission done the switch got out of alignment.  Now the car will start in Park, but not in Neutral,…Continue

Tags: issues, Switch, Neutral

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 27 minutes ago. 9 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 19 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

Carpet install

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 1 Reply

simple question, Does the carpet go under the seat mounts and bolted down with the seat? My original carpet was cut to go around the seat mounts looks like a hack job. Same with the steering column,…Continue

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service