Hello, and thanks for adding to group!

I am restoring 1964 429 engine which I bought as dismantled. It is said to be smoking in driving and has been stored as parts for a year. It is most probably 65500 miles driven. Car was not driven for10 years.


The only damaged part found so far is the top of exhaust valve of cylinder #5. The top has been worn so much that the rocker has been pressing valve locks as well. Respective rocker is worn as well, much more than others. And exhaust rocker #6 is worn as well, and exhaust #8.
Then questions:
1. What damage could this cause? I can think that valve lift gets a bit smaller than it should, but so what?
2. Is that common for Cadillac 429 exhaust valves to worn from the top, especially cylinders #5 and #6? Maybe there is less oil.

This is my first V8 engine project. I have Shop manual. I plan to replace piston rings, all gaskets, nylon timing gear, some worn exhaust valves and rockers, and valve stem o-rings. Bearings, pistons and shafts are in good condition. 

Big thanks in advance!

Views: 1006

Attachments:

Reply to This

Replies to This Discussion

The THM to Adaptor ring are the longer bolts. Here are the specs:
- THM Trans to Adaptor Ring: 7/16"-14 1 1/2" Long Grade 5
- Adaptor Ring to Engine: 7/16"-14 1 1/4" Long Grade 5

Of course I have them cad plated but yours like in fine condition.

Thanks Jason!

I have been busy with 66 coupe and new acquisition 67 convertible but now I decided to focus in getting rebuilt engine and th400 finally into 64 Engine Bay.

Attachments:

Matti 

Approaching the — IT’S ALIVE !!!! ——IT’S ALIVE !!!!  — let’s go for a Drive ! ——moment —LOL ! 

Enjoy 

Should I get good compression results in cylinders when rotating engine manually slowly from crank bolt? Reason for asking is that I get very low numbers in meter. Engine is still in engine stand.

i could install adapter ring and rotate with starter to get proper results.

Matti 

You will never get a good compression reading from the cylinders until the new  rings seat to the cylinder walls —( valves seat - cam seats —etc )  only from putting miles on the engine 

The rings in our engines— are exceptionally hard metal and take a bit longer to seat than most for that reason 

You will be burning more oil than usual for the first 500-1000 miles so keep an eye on the oil level at that time 

It is  my opinion it takes 10,000 miles to seat an engine  completely and SB done with conventional oil ( not Syn oil ) or the seating will take longer to happen 

I do not exceed 50MPH during that time varying your  speed constantly 

Coming off the gas at 50 MPH  down to 30 MPH  will lube the valve train 

Your next challenge will be ——-preparing the engine to fire up  —-as quickly as is possible and get the RPMs up over 1000 RPMs for a half hour as that is what seats the metal to metal surfaces —to polish themselves together being the single thing to determine the engines long term health into the future 

Mostly it’s about installing the dist correctly —having the points set  ( must be set with a feeler gauge - .016 ) and the timing as close as is possible to its mark ( 5-8 degrees ) for an instant fire up ( gas in the tank ) 

So a very very  important time and  step 

Hope that helps some 

Varoooooooom !! 

Enjoy 

Change your oil at the first 1000 miles after a new engine start up 

My results doing the above has  resulted  in an engine that burns no oil for its life time being a new engine rebuild or new car break in 

Enjoy 

I plan to use Edelbrock 1406 from my 66 for 64 engine break in. It works fine now in 66 so it should work fine in 64 as well from the beginning.

Matti 

Your carb  plan sounds like a good one

Not a good time to be fussing with a questionable carb —be it old or new( requiring adjustment )  at a new engine start up and run time 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Transmission vacuum modulator

Started by Sammy in 1963/64 Cadillac Specific Discussion 1 minute ago. 0 Replies

Today I started to exchange all old vacuum hoses under the hood.The one going to the transmission vacuum modulator is really hardened out, but I can't get that thing out.Is it screwed or pushed…Continue

64 Coupe deVille convertible

Started by Fab in For Sale. Last reply by Fab 1 hour ago. 6 Replies

Great condition, car is a driver, not a show car, but can be one with not much more work. Laundry list of items that have been updated, refreshed, rebuilt, etc. Reach out for details, too much to…Continue

Question about the 1963 Hydramatic Oil-Filter

Started by Stefan in General Discussion. Last reply by Russ Austin 3 hours ago. 12 Replies

Hello everyone,Has anyone of you ever opened the transmission filter and can tell me whether there is filter fabric in there or a metal screen, that can be washed out? The number on the transmission…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Fuel Pump Failure

Posted by Jon Shields on August 6, 2022 at 6:48am 3 Comments

Hello,

I'm located in Melbourne, Australia and my 64 sedan de ville is stuck in the garage due to failed mechanical fuel pump. The first after market mechanical fuel pump lasted a few years before it failed & left me stranded 5 hours from home. A hire car and tow got us home. On inspection, I noticed a valve not seated within the housing. I was optimistic, pressed it into place and assumed the pump was good to go. But alas, no. From what I can now determine, the diaphragm pushrod…

Continue

Renovation project 1964 Cadillac Deville convertible

Posted by Balachne on May 31, 2022 at 7:00am 3 Comments

Renovation project 1964 Cadillac Deville convertible

 

Introduction

To achieve an excellent result of vehicle restoration, it is essential to  manage this task as one manages an industrial project.

To do this we will use a certain formalism of project management and therefore start by defining the need. It is from this that we will deduce the scope, then the time of execution of the…

Continue

I was working on my HVAC system this winter and during the process of taking the dash pad off these two parts fell out. Does anyone know what they are and where they go?

Posted by Patrick Westphal on April 12, 2022 at 1:35pm 1 Comment

I was working on my HVAC system this winter and during the process of taking the dash pad off these two parts fell out. Does anyone know what they are and where they go?

1964 Cadillac Coupe DeVille Convertible Speedometer Bulbs

Posted by Russell L Parr on April 1, 2022 at 9:15pm 6 Comments

I need to replace the bulbs for the speedometer cluster in my instrument panel..

Before I open up the dash, I want to have the necessary bulbs on hand.

Can someone help me determine what bulbs I need, the number of bulbs I need,  and where to purchase them?

Your help will be greatly appreciated.

Videos

  • Add Videos
  • View All

© 2022   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service