I have purchased a 1963 4 door cadillac that was stored since 1974.

Its a minnesota car but not that bad. the quarter panels are still good,3 of 4 doors are good. the dash is mint.

the front end is complete, but the right end cap lower is shot. left is fixable. 

its a blue car with blue interior, which is in pretty good shape. 

I will tell you that the boomerang pieces and the hood is already gone to my project car. 


Views: 260

Reply to This

Replies to This Discussion

you can email me direct at 38bmod@gmail.com

by end of november it may go to the crusher

its going to be gone sooner than that. 

Walt, If you were closer I would be interested. I would suggest trying to find someone near by that could either dismantle the car and put parts up in dry storage (as I do with my parts cars), or stick it under a shelter somewhere and pick parts off as needed. There is eventually a demand for almost everything usable off these cars but it doesn't occur within 1 month. I like to repeat the fact an old car like this breaks down to about 5000 parts and I probably still have 2000 parts from that 1st parts car I brought in back in March 1997 ... and am very comfortable with that fact since I am in it for the long haul. If you just post a car on Oct and say it is going to the crusher in Nov, you may move a few very high demand parts... and that is if you are lucky.  Just relaying my experience.

I pushed it into my grove of trees for now. I'll get pictures of it an post.

Some pictures of the car might help you move some parts off of it.

Where are you located ?

How many miles on the car ?




  • Add Photos
  • View All


Rear shelf deck

Started by mark zimmerman in 1963/64 Cadillac Specific Discussion 43 minutes ago. 0 Replies

Hi does anyone know what yo have to do to remove the rear deck board that covers the speaker and defroster? is it screwed down ?glued?ThanksContinue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

I Whipped Out My Horn and Waxed It Today!

Started by Jason Edge in General Discussion. Last reply by john w. warner on Friday. 6 Replies

This got some humorous replies on Facebook and wanted to share here on the 63/64 site.I was installing the lower hood latch with all the new gold cadmium bling on my 64 Coupe de Ville "Dino" today…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…


New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …


Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…


Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment


Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…



  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service