Hello everyone. I had a perfectly good shifting Hydra-Matic transmission until I elected to fix the leak at the dip stick tube. I just did a quick seal with gasket maker since my current tube is missing the mount and I was headed to the Lead Sled show in Salina, KS in a few days. I drained about 2 quarts of fluid so I could do a good cleaning around the inlet and under the dirt flange of the tube. Installed gasket maker and reinserted the tube then let it sit for 24 hours. Topped off the fluid level the next night and took it for a test drive and now I only have park, 1st gear and neutral only. I have run the diagnosis in the manual. Reverse table is normal, low table is normal, third table has no 2nd, third or fourth, same results for fourth table per the manual and neutral table is normal. I would think I could assume no broken parts and this is a result of possibly stirring up debris from refilling the transmission. If so if I get into the valve body will I need new seals or is it a take apart clean and reassemble process? Could the governor be suspect and if so should I start there?

On the bright side I did stop the leak.

Thanks

Norm

Views: 167

Reply to This

Replies to This Discussion

The valve body is somewhat protected by the filter, and is usually 'self-cleaning'.   I actually doubt that silicone would survive long in there.  I'd focus first on the governor weights, then drop the pan and clean it out.  I would try refilling and running it at that point, only removing the valve body if it still didn't shift.  If any debris got into the line pressure feed, it would really not be likely to get past the governor's spool valves and into the passages, but i guess it could potentially.

Thank you again for all your help and knowledge. If the gasket gets here tomorrow I’ll give it a shot!

Mark 

Thank you much for your explanation and  your understanding of the Hydramatic trans 

love when a subject gets the attention it does on this super site for our year Super Classic Antique  Cadillac owners 

Enjoy 

It was the governor. Both valves were stuck, a good cleaning and refill and all is good. I was amazed at the torque someone had but on the rear extension bolts. I had to use a half inch impact wrench to break them loose! Same at the universal flange to pinion. 

Thank you again for all the help. 

Norm
Very happy  you are back in action with some time and help from your Cadillac friends and minimum expense 

Enjoy having her back ! 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 9 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 10 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 17 hours ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service