64 AC : Blower runs, air is felt at firewall, but not through heater outlets or AC vents (HEAT/AC door WORKS)

Hello All.

As I am getting in to this troubleshooting with the benefit of Tim Groves invaluable book, I find something that is not covered; blower works strongly but no air can be felt either at heat ducts or AC ducts even though the Heat/AC mode door DOES WORK when I apply vacuum to the solenoid that controls it. (thanks to Tony and Ginny 429 for clueing me in to what panel to remove to observe the door). 

As luck would have it, I have buddies who own a MOPAR junkyard and one time they took in a 64 CDV with AC. So I managed to get some parts off of it to practice on and to use. I got what turned out to be a good Transducer and installed it, so now when I run the temp wheel the Power arm moves from AC to heat and changes the blower speed. HOWEVER, nothing comes out of anywhere even though I can hear the blower working hard AND I can feel a STRONG rush of air all the way in the back near the firewall. I had thought what I was feeling was the INTAKE for the blower with the RECIRC door stuck open (solenoid inop), but now I am not so sure. 

When I stick my hand inside the heat/ac blend door I can feel that something is flowing, but not alot; it sounds/feels like there's lots of air moving, but not in the right direction. 

Stumped!

All replies welcome, thanks.

Norm

Views: 694

Reply to This

Replies to This Discussion

this was the project. It included the whole comfort control system, electric fans and shroud, transmission cooler electric fans, fitech fuel injection and some paint under hood. Also all new rubbers and insulation under there as well.

Have not taken the inspection plate (inner fender well) off yet, but noticed something: The heater/AC brown vacuum hose from the control unit nipple is not giving vacuum to the solenoid that operates the door. When I give the door solenoid vacuum, it works fine. So, I need to take the 7 nipple valve body out of the control unit and replace it with a spare I have that I think works ok. BUT: How do I remove that friction clip that holds the valve body on to the peg-without ruining it, so I can use it again when I put the replacement valve body on?

Norm, are you sure the rotary valve is getting vacuum?

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith yesterday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Events

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service