My bench seat switch circuit is dead.  I found the hot wire cut under the seat, but cannot locate the other end of the hot wire.  The wiring diagram indicates the it is connected to the rear cigar lighter hot. (See attached)  Is this right?  Does anyone have any thoughts about where I may be able to locate the or, or splice in?  Thank you.

Views: 150

Attachments:

Reply to This

Replies to This Discussion

All of the bench seat wiring feeds from the left side under the door sill plate. Remove the finish screws that hold the driver door sill plate down, remove plate, lift carpet and see the plastic wiring conduit. There is a cut out on inside neareast front corner of seat where the wire's "T-out" toward the seat. They are held down with a couple of red primer color clamps held with Phillips screws. See if you can see the other end of your wire and trace to the cut area and splice back if everything else looks OK. 

Thank’s Jason. I see what you are taking about. I’ll send a pic.
I ran a new wire and spliced in a new connector. The seat back switch now works and the lights come on. Only thing is the courtesy lights also come in the front driving compartment as well when I flip the switch. Aren’t only the rear courtesy lights supposed to come on?

Interior lights with the switch at the back of the front seat— in the convertible are working as they should from your description 

Enjoy

Thank you for your post. All four interior lights (2 front/2 rear) come on when I turn on the seat back switch. The owners manual says the sear back switch will turn on the rear lights only. In the convertible all 4 are supposed to come on with seat back switch?

Hmm, In my 63 CDV only the rear courtesy lights come on when the switch on the back of the front switch is turned on (according to owner's manual too). I believe the circuit works by grounding the lights with the pin switch in the door jambs or with the switch on the back of the front seat for the rear courtesy lights. It seems your switch is grounding for all interior lights. Could be bad door jamb switch(es) allowing the ground for all lights

.

Kurt, I don’t think it’s in the door switches. In fixing the rear switch circuit yesterday, I realized the bench seat wasn’t grounded (also causing the seat motor not to work). I grounded the seat by running a wire from an arm rest bolt (behind the fold down cover) to a wiring clip screw under the carpet. Bingo! The seat motor and back seat light switch worked (after rewiring the hot leads).

I had an issue once where turning on the map light would also turn on the courtesy lights. It was the the pin switch allowing grounding of the courtesy lights. If not the pin switches, trace out what is allowing ground to all lights.

You know what? As I think about it, I recall when I replaced the door switches about six months ago, i bought 2 prong switches (couldn't find 3 prong) and jumped the hot for the four lights to work. I think you might be right: it’s likely the front door switches.

Without the 3 prong switch, 2 circuits are tied together meaning grounding one will ground the other. I guess you can chose whether to tie the map light to the front courtesy lights or leave it as is. A 3 prong switch is what you need to separate the circuits.

The 2 or 3 pin door jamb switch keeps the circuits separated.   if you out in a single wire door jamb switch, all the lights will come on. 

Russ, do you think I jumped the wrong prong on the two prong switch, effectively making it a one prong)? I could move the jump to the other prong?)

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 13 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

You Know You Are Into Some Serious Car Doctor When You Have to Get the Ice Out!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 17 Replies

You know you are into some serious car doctoring when you have to get the ice packs out. More to come on my 64 Coupe de Ville resuscitation in the next 1963/64 Cadillac Chapter Newsletter!  Mades…Continue

Unknown part, maybe the last one?

Started by Matti Roth in Restoration Discussion. Last reply by Jason Edge yesterday. 1 Reply

Hithanks to great help from chapter members I am getting my 64 Deville ready, slowly but surely.There is only one part still unclear, or actually three bolts and nuts. They are clearly different from…Continue

Leaky Windshield

Started by Tom Bahner in General Discussion. Last reply by Tom Bahner yesterday. 4 Replies

Hey all, has anyone had their windshield removed and resealed successfully. I'm pretty skittish about having someone mess with my perfectly good glass knowing that these cars are a little different…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service