Has anyone drilled the backing plates and made the slots that allow brake adjustments without removing the wheel?  I have always hated the slots in the drums.

Views: 68

Reply to This

Replies to This Discussion

Doug 

I am in complete agreement that adjusting the brakes with  the slots on the front of the brake drums are more work than they could be due to  moving around the very large tires and rims on our cars adding to the task 

Been on here daily since 2006 and no one I know of has cut slots in the back plate to answer your question 

There are stock self adjusting brakes on our cars unless they  have been eliminated 

When the self adjusters are working as they should  all you need to do is back up and feel the brake peddle get harder to the touch 

I do all my own brake work on all my cars over the years and find that I only have adjusted the brakes on my 64  from the slots only  after I did brake work on my 64 ( replaced brake shoes etc ) to get the brakes adjusted correctly at that time only 

The self adjusters however can cause problems when not working as they should by tightening up the brakes and causing them to drag causing excessive  heat issues and damage the brake shoe material or making the brake to loose to be effective as well 

Self adjusters not working as they should  can cause wheel pulling issues regarding the cars steering which is a problem 

I myself have never thought about or considered cutting slots in the back plate as the self adjusters have kept my brake adjustments in good form for myself 

I would recommend replacing all brake springs when doing a brake job on our  old cars as the spring  fatigue due to the constant heat and cooling they are constantly subject to causing the self adjusters to not as they should be over time 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service