I think I might have a broken rear spring. 

Took the car for quick test drive today and sent little bump I hit, I could hear a thud like it was bottoming out. Come to see when I got home, the driver side rear is squatting really bad.  I forgot to take a pic but a good 2 inches. Did I break a spring? I can't see anything from underneath.

Views: 217

Reply to This

Replies to This Discussion


Be sure nothing is interfering with the shocks travel on the sagging side as you said something about a muffler clamp making contact 

Enjoy 

I'm guessing its a combination of all the above. The exhaust hitting the shock looks more like the culprit. I'll need to replace the bushings anyway there all cracked anyway.
Appreciate your help kind sir

You are very welcome 

If you are talking about replacing the trailing arm bushings let me know as I can steer you in the right direction as there is a Major issue regarding replacement trailing arm bushings on our car at this point in time 

All available bushings on the market are short lived except for an after market supplier who is making replacement arms for our cars 

Enjoy 

Well thanks for the tip.

Do have to replace the whole control arm?

Yes 

Dan McNarry makes new arms with poly bushings that are not stock but stronger and not easy to see because they are under the car 

They are the only true bushing replacement  solution we now have at this time that will give you more than 400- 600 miles before the new replacement bushings will go bad which is not acceptable at all 

Enjoy 

Dans contact info is in —Part Supplies — in the header under Dan’s control arms 

Your very best solution for those bushing replacements 

Dan is a SUPER  CAR GUY and amazing engineer 

Enjoy 

Thanks again wow this club is awesome

Just priced bushings on OPGI and its nearly $400 just for the bushings. Smh

All on market are the same bushings as only one company makes them no matter what supplier you use —- Junk 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Roof trim

Started by Krystin Barany in 1963/64 Cadillac Specific Discussion. Last reply by Krystin Barany 31 minutes ago. 2 Replies

I’m going to be starting to tear down my 64’ DeVille before too long but one thing I never figured out was how the roof trim comes off. I understand the drip rails and how to take those off without…Continue

Factory AC clutch fan needed

Started by Chris Gill in 1963/64 Cadillac Specific Discussion 3 hours ago. 0 Replies

Hi folks,My clutch fan died so I desperately need a new one. Unfortunately it will take a week or more to order from the usual suppliers so I am hoping someone on here has a manufacturer name and…Continue

Replacement Rear Trailing Arms

Started by Dan McNarry in Restoration Discussion. Last reply by Kim K Kaiser 7 hours ago. 5 Replies

Hello all,I haven't been on the forum for quite a while and do wish you all well. I would like to thank all of you who have purchased replacement rear trailing arms from me in the past. I realize…Continue

Over heating

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 4 Replies

Hi, been doing the break in still. At about 450 miles.I hve noticed that when i go out, temp gets to between 1/4 and 1/2 on the gauge.  If i sit any period of time or dnt keep moving, it creeps…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service