I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at www.facebook.com/classiccadillacparts and will post a few here  on this thread from time to time.

For items you are interested in send email me to jasonedge@nc.rr.com   

To save us both time be sure and provided details including year, body style, color, location (left or right, front or rear, etc), and any other information I need to identify the part. 

ps... be sure and "Like" my page!

Jason.

Views: 23126

Reply to This

Replies to This Discussion

1964 Sedan de Ville Rear Arm Rest Set (Turqouise) - $125 pr, $65 ea <--- Click for More Pictures

I have a very good set of 1964 Sedan de Ville Rear arm rests for $125 for the pair, or $65 each. The plastic is excellent and leather on the padded section is VG. These are Trim Code 46 Turquoise and can be sprayed to match your interior. Email me at jasonedge@nc.rr.com

1964 Fleetwood 60S Arm Rest Set (Lt Blue) - $150 <-- Click for More Pictures

I have a Good To Very Good set of 1964 Fleetwood 60 Special arm rests with trim code 63 Lt Blue for $150 for the 4 pc set, or $50 Each. Email me at jasonedge@nc.rr.com The left front has a nice side but some wear on the top, the right front has very nice side and top pad. The 2 rears have nice top had but some minor indentations from storage on the sides.

New Rebuilt Duralast 7122 55 amp Alternators - $50 each

I have a couple of new rebuilt AutoZone sourced Duralast DL7122 55 amp direct replacement alternators for $50 each. That is $20 less than current price without core. (They are $55 with core). Email me at jasonedge@nc.rr.com.

1964 Fleetwood 60S Rear Arm Rest Set (Lt Sand) - $75  <-- Click for More Pictures

I have a Very Good set of 1964 Fleetwood 60 Special rear arm rests with trim code 64 Sandalwood for $75 for the 4 pc set, or $50 Each. The light sandalwood is the worst color in terms of showing stains, etc. but these have held up well. The top leather pads are VG condition with only minor wear, and the sides are good with only slight staining in a couple of places. Email me at jasonedge@nc.rr.com

RSS

Photos

  • Add Photos
  • View All

Forum

Back to Starter

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 2 hours ago. 54 Replies

Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag…Continue

'63 CDV Restomod on Iron Resurrection on Velocity Channel

Started by Ian Osborne in General Discussion. Last reply by Russ Austin 7 hours ago. 1 Reply

I just watched an episode of a show called Iron Resurrection on Velocity Channel. They did a restomod on a pretty clean survivor '63 CDV for a customer. They did an LS3 swap, air ride, complete…Continue

1963 Ignition Bezel

Started by Lee Martin in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 7 hours ago. 2 Replies

Looking for a good ignition lock nut bezel for 1963!  This is the chrome piece that holds the ignition housing in place and protects painted dash from key scratches.  Opening must be more than 15/16"…Continue

Floor Pans

Started by Tommy Nicolosi in Restoration Discussion 15 hours ago. 0 Replies

Are the floors on 1961-1964 the same???Continue

Blog Posts

HVAC Vacuum Valve Clip-need the one for the Power Control side

Posted by Norman Silverman on September 17, 2018 at 8:15pm 6 Comments

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy…

Continue

7 vacuum valve-need a good one or someone to recondition mine

Posted by Norman Silverman on September 15, 2018 at 5:44pm 12 Comments

So, I've put my 7 vacuum valve from the control head side to the test, and it failed. I looked at the instructions for re-conditioning it and unless I am missing something, the instructions are missing something (about how to take off the clip that provides the tension that holds the two pieces together). 

In any case, I can't do this particular repair so I am looking for a new valve (not likely), or a good re-conditioned one, or someone who has done this before and would do mine for…

Continue

Mosiac Cadillac emblem Table

Posted by Dana G Cooper on August 30, 2018 at 10:48pm 11 Comments

Wanted to share a picture of a table my wife made for me to display with our 63 Coupe Deville. 

Inside door handle thread size

Posted by Michael Jarnagin on August 23, 2018 at 4:31pm 1 Comment

Anyone know the thread size on the inside door handle bolts mine are missing any info much appreciated 

Events

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service