Adjusted timing bck towards advance, ran much smoother.  Only a couple initial pops out of carb.  Replaced carb gasket w felpros, no sign of leak there.

Got about 30 min of runing at 1250 to 1500 rpm.  Oil pressure was good,  32 to 34 initially. Down to bout 28 at shut off.  Engine a little hot at end almost half way.

Some popping noises inside.  Like internal backfires.  Not metal, but there all the same.  And frequency increased as i approached 1500 tp 1600 rpm.

One thing at back of valley pan that worries me,   note color of fluid.  Id that oil n antifreeze?   Normal during breakin, or are my head gaskets not holding?

I will ck a couple videos to utube, see if that thumping is visible and any other things anyone may see or hear.

Timing at 1500 was about 5 to 7.  Seemed smoother there

Photo attached20210413_124707.jpg

Views: 139

Reply to This

Replies to This Discussion

Yes, i out white out ib the markee

Try turning the dist counter clockwise  so slightly until you can get the car to idle at a lower Rpm

Enjoy 

I tried to go CW but engine wont hold up to run at 450/480.  Gonna hv to put on hold for a bit

I am currently putting the car on my trailer and beginning long journey back to montana for summer and tge busy tourist season.  Takes me about four grueling driving days to get thrre from MS.  I will try to get back on it when i get back settled up there.

I had always hooed from beginning to hv it running by this time,  but as tgey say, best laid plans of mice and mem.

Thanks to everyone who has had thoughts and comments on my adventure into this rebuild,  coukdnt have gotten to this point without everyones help.and thoughts 

Kim

Kim
Have a safe trip back to Montana 

Enjoy

Been a while since i cked in. Got bk to montana w car in tow. Had some offline instrction on rochester, tuning etc in the meantime.  

Backfiring was from hving 2 & 4 spark wires crossed.  

My bent tv rod was preventing the accel from going all the way back, so got idle back to 500 w timing at 7 to 8.   

Had some instrction by using both vacuum gauge and rpm tp try and set carb.   Not sure were it stands right now.   

Engine runs half way between 1/4 andv1/2 temp while sitting at idle.   

I took for short ride today.  Thought i had trans prob for first 50 yards. But remebered fluid was out so put 5 quart in.   Took about 4 loops around block.  Some adjustment gonna be needed at tv rod i think.  But engine seemed to feel a bit more strong.  

Temp is worrysome though, it was a full 1/2 for the short ride.  Going to put infered on it at the temp sensor, see what that says, isvthat a good place to point it for this measurement?

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 18 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service