I have been replacing underhood items on my 64 Cadillac Coupe de Ville 'Dino' with freshly Cadmium plated parts and need to replace the hood hinges so I had my brother Randy come help take it off and put in our Parlor (no where else to put it righ now). I'll replace the hood hinges but also take advantage of the easy engine access and replace lifters and push rods and freshen up the engine and engine bay a bit. Here are some of the topless pics of Dino outside.

Views: 139

Reply to This

Replies to This Discussion

Jason 

That hood is no joke to be moving around for two strong guys 

Very glad you are getting to repair your engine issues due to being so very busy building extensions on the home for some time 

Sure you will Love having Dino back  to running great and the happiness that that brings us all 

Congrats on the success of the cadmium parts sales and your car looks awesome with those parts you have added which go exceptionally great with the Sierra Gold  color of your ride 

Very nice attention to detail which is your   legacy 

Looking  very  very Sharp my friend !!

Enjoy 

The car is truly stunning ! 
 Enjoy 

How many miles hv you been since your 12 rebuild?  Why would you be replacing rods and such.  Are you simply doing an upgrade to them or is this something I may be looking forward to as well after rebuild?  Or is it life w old engine?

Kim, I have had a dead valve lifter on the right side near rear and need to replace the lifter. Instead of replacing just the one I am replacing all lifters and push rods. I have put 3000 to 4000K miles on the car, almost all before the lifter tick started in May 2019 (engine rebuilt May 2012). I've had too many projects to tackle this rather easy fix (hoping it doe the fix) and have limited the car to short drives.  As most of you that know me, know I generally never get in any hurry. I took 3  months to rebuild the engine block, (cylinder heads had been rebuilt way back).  With the hood off I will be pressed to start this dismantle process and while I have the top popped off will go back thru the clean up and repaint process to get it looking spic&span again! I would like to think I would have the engine ready by summer, but also have a new dining room & pantry addition started with my 1912 house.  As they say "Life is a journey, not a destination”.

There was a reason dean martin was never shirtless. For gods sake dino, either turn off the lights or put some clothes on. And come back to bed.

I'm afraid Dino will remain shirtless for some time.. probably several months. In fact the hood is now in our Parlor! I really didn't have any place to put it where there is almost no chance I might run into it other than that room.  With the hood off in the garage, there will definitely be more incentive to fix some things... to mention replace all the bolts with the new Cad stuff.  Today the hood hinges came off and are in the bin of large stuff to Cad Plate. These were nice tight hinges, and when I scroll up my Wait List when I get them back someone is going to get some really nice hood hinges!

Jason, you are probably already aware of this, but just in case.... make sure you use oil with a good amount of  ZDDP content with those new lifters. Don't take chances with that cam! Double check with someone if they need a run in or not. That might apply just to the cam, which of course you did back in '12, but I'm not positive or not if just liter replacement needs that.

My machinist gave me 5 qts of Lucas break in oil for me to use in mine for first run, but then, my whole engine was just rebuilt ground up. It can't hurt to be careful.

My 64 has not tasted any oil other than the Valvoline VR1 high zinc/ZDDP content oil since I bought it in 1996. I'm just not a fan of chunking additives in oil, and would rather just pay an extra couple of bucks and run oil with higher levels of ZDDP already in ot.

With that said, I will add 2 things I believe true:

1) Too much ZDDP becomes corrosive. From memory it is over 2000 ppm. So dump too  much additive in your oil and it can be more harmful or helpful. So if you are using additives don't just dump a bunch of ZDDP additive to your engine oil and hope for the best. The VR1 oil has about 1200 ppm as I recall which is a good amount for older engines.

2) Unless you are constantly driving your car hard, I mean very hard, high rpm high miles the current oil with the reduced ZDDP levels is probalby not going to hurt a thing... but I am like as much preventative maintenance as the next person and feel the VR1 as right for me. I don't have to worry about too little or too much ZDDP.  Just run as you do any other oil.

Thanks for the tip on that oil! I'll try that oil when the break in period is up. I agree that if you already have oil with ZDDP, then additive should not be added. It's only the last year or two that I became aware of the ZDDP issue.

Next time I see the machinist I am going to ask him about run-in for lifters only, with an already run-in cam. I suspect that it is not necessary to run them in, but it will be good to know for sure, for future reference.

Roller cams are supposed to be nearly immune to flat tappet wear issues, but my danged 01 Corvette with 72K on the clock wiped the cam last year due to a roller lifter. Roller spun nice, but we think it wasn't hardened properly. The surface of it was nasty, and wore a nice deep track in the cam lobe. Misfire at idle was how it presented.

BTW, that plated hardware looks mighty fine in there!

RSS

Photos

  • Add Photos
  • View All

Forum

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 8 hours ago. 5 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 hours ago. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 23 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Organizing For Sale?

Started by Anders in Suggestion Box. Last reply by Jason Edge yesterday. 1 Reply

Been looking on the For Sale forum. Not sure if possible or not, but it might be good if there would be sub-forums so cars go in one area and maybe spares could be sorted in a way as well. No idea…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service