Views: 660

Reply to This

Replies to This Discussion

I had a similar issue when I installed mine. Turns out they are giving me a bad proportioning valve, which they replaced for free.
They’ve already replaced the prop valve for the disc-disc setup and still it does slooooooow down...
start to regret the fricken ‘conversion’

Those are self adjusting calipers...or maybe there’s a trick to it...?!
What was the ‘washer’ issue you had???
What washer are you talking about ?

Hey Joe D 

Glad to see you pop in from time to time 

Your Caddy must be running good for you not to be around much — a good thing !!  (  per Martha Stuart ) 

Enjoy 

When you call the company —-ask them what needs to be done for there brakes to stop your car as they should be doing —-and leave the burden of solving the problem to them 

Speak only with the person in charge ( hopefully the owner ) 

I think—— the proportioning valve is only used when using discs on the front and drums on the rear to balance the braking system pressures 

Are you sure your brake installation was done correctly at the wheels ?  ( caliper washers in the correct place as Joe D explained in a prior post - or other installation issues ? ) 

It feels like there is not enough pressure in your braking system to be pushing the caliper pistons into the rotors hard enough to make proper contact with them —-and stop the car 

Was the power booster —-and the master cylinder —new and replaced as those control the pressure to the system 

The master cylinder — may be a part of the issue as that controls the brake fluids pressure in the braking system 

If the MC was not replaced   ( or could be  new defective )  that W/b the first part I would be looking to replace with this issue myself  ( after the companies suggestions ) 

The type of brake fluid used could effect the systems pressure making the peddle feel softer than other brake fluids 

Be sure you have the recommended fluid for your braking system now 

Do be very careful with the brakes not working correctly — can be dangerous 

That S/b a good start to get to the bottom of the problem 

Enjoy 

Your power booster arm to the MC may not be adjusted correctly  internally possibly applying less pressure than it SB to the MC and not allowing the master cylinder internal arm to travel as much as it should to build the correct pressure in the system 

Again effecting the pressure in the braking system in a negative way when not properly extended 

Just my best guesses based on the symptoms 

Enjoy 

Last year I went over the Master Cylinder and a Booster, measured the internal arm etc... everything is correct!

I dont get that ‚washer’ issue JoeD talks about... too bad he’s not participating in this conversation.

I am having problems with my front disk brake dragging.  The temperature is 130 with no brake usage.  It that to hot? Dave

Dave 

i have no idea about disc brake temps but that logically seems like the temp SB high if they are dragging ( excessive friction ) 

That will cause premature brake  pad wear for sure 

Brakes dragging could cause issue with your Trans as you can be overworking the trans and raising the temps it runs at (  a strain ) 

You need to find the cause of the brakes dragging issue and repair it 

If you have the proportioning valve on the front I would be thinking that could be the issue if it went bad 

I assume the front discs were not dragging  and working correctly at some point in time and then started to drag on you 

Enjoy 

Dave 

Same advice to contact your disc brake company and explain your issue and see what they have to say for a possible solution to the dragging pads and go from there 

Enjoy 

The washers go between the caliper and it’s mounting bracket per Joe D’s Post near the beginning of this thread  ( his  post starts out answering a question  by Clovis and then me )

Enjoy

The washers go between the caliper and it’s mounting bracket per Joe D’s Post near the beginning of this thread  ( his  post starts out answering a question  by Clovis and then me )

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Power Brake Booster

Started by Stephen A. Pechenik in General Discussion. Last reply by Tony and Ginny 429 3 hours ago. 4 Replies

Hello Co-Members,I recently purchased a  low mileage1963 Sedan Deville Park Avenue.  It is extremely solid and runs well.  Neverthelss, it has minor problems that need to be addressed before I can…Continue

Jeremy LeBlanc

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 4 Replies

Jeremy I am very interested in learning all you can tell me and the community about your engine swap to the 2019 LS2 L96 Silverado engine and 6L90 trans you installed in your 63Any details you could…Continue

Tags: 63, to, swap, engine, Silverado

Dan McNarry

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 9 hours ago. 5 Replies

Dan Have you come up with any solution for the front bushings of the rear trailing arms of our year cars ?I thought you had suggested you were thinking about what you might do about that Stay Safe Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 21 hours ago. 178 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

1964 Cadillac fleetwood sixty special vanilla top windshield needed

Posted by Pablo on April 5, 2020 at 10:00pm 3 Comments

If anybody has or know where Can I get a windshield glass for my 1964 Cadillac fleetwood sixty special with vinyl  top? I will appreciate any info.

Thank you very much

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service