HI all,

I have finally started the project of restoring my '63 Coupe. Problem is I inherited a few headaches and little actual info. The previous owner(s) have left the car in various states of disassembly. I didn't even get a set of keys with it. That leads me to my question.

It appears as if the trunk is FULL of various parts I looked after taking the back seat out). Problem is that I can't get into it! As mentioned there were no keys. I popped one of the door locks off and had a key made for it. Unfortunately this key only works in both doors and ignition. I always assumed that this car would be like every other GM I've owned in where the doors and trunk were keyed alike and the ignition was it's own key. I guessed wrong it seems. What am I going to need to do to pop the trunk? Is the trunk key the same as the glove box key? I've tried pumping a blast of air into the vac line for the trunk but only get a slight hiss coming from the trunk area. It's imperative that I get into that trunk to take stock of whatever parts may be in there. I'd hate to buy up a bunch of stuff only to find out they were in the trunk all along. Advise me please.

Thanks,

Greg

Views: 376

Reply to This

Replies to This Discussion

Minor update: The glove box is keyed the same as the doors and ignition. I would assume that the trunk is as well but the key refuses to budge the lock. I have jiggled and wiggled it six ways from Sunday and no dice. Short of calling in a locksmith (which I loathe to do) I'm out of ideas.

The door and ignition are the same key. the glove box and trunk are the same key. Since you have the power trunk, put vacuum to the line going to the trunk. Hopefully you get lucky with that.

If not, take the glove box lock out.  The lock has no numbers stamped on it, but a lock smith can easily look at it and tell what the code is.   Hold the chrome bezel still, and move the glove box lock assembly back and forth. that should loosen up the bezel. It just unscrews and the lock will fall out.

Or take a 7/16 socket and get it to the 3 bolts that hold the trunk latch in the deck lid.  The deck lid would then lift up.

How do our car locks get so screwed up!! My door and trunk is the same key and the ignition key is different. I've never tried the glove box yet but I am going to now.
If you attach a hand vacuum pump to the trunk power release that might work.

Thanks to all that replied.

I eventually got the trunk to open. It took a lot of patience and jiggling of the key to get it there though. It seems as if the tumbler for the trunk is worn. I'll have to take it to the locksmith and get them to repair it. Unfortunately the vacuum trick didn't work this time but I got it to open eventually. Patience is a virtue.

It seems that at some point someone had all the locks and ignition keyed the same. I'm okay with that but I still prefer the "old school" way of having the ignition and doors keyed differently.

Cheers,

Greg

Greg my door locks didn't work when I first got my car. When I realized what was going on I sprayed wd40 in them and now they work perfectly. I originally thought I had no door keys.

This thread reminds me of the most overlooked piece of literature most of us have ... our owners  manual.  Page 4 is all about the two separate keys provided - octagonal head for ignition and door locks; rounded head for luggage compartment and glove box. Read that owners manual and you will be surprised at the wealth of information. If anyone needs one I have a very good 1964 manual from last parts car for $25 + s/h.

The ignition key can be removed while the car is running ,which is different to me ,from other cars
Helps if you need to get to the trunk key
Do not lock your keys in the trunk ,by accident
That is what a Hide a Key is for
I find a Hide a key to be a very good idea ,when it is needed
I have been using them for about 50 years on all my cars
It can truly rescue you when needed

Enjoy

That just means that the key is worn. The key should not be able to be removed when the switch is turned on.

Russ is correct. I've had a few driver and parts cars where the key would remove when switched on, but that is from a worn key and/or lock.

Still using the original keys ,so a lot of room for wear over 52 years
Interesting to learn ,wear is responsible for the convienence it affords
Thanks guys

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service