HI all,

I have finally started the project of restoring my '63 Coupe. Problem is I inherited a few headaches and little actual info. The previous owner(s) have left the car in various states of disassembly. I didn't even get a set of keys with it. That leads me to my question.

It appears as if the trunk is FULL of various parts I looked after taking the back seat out). Problem is that I can't get into it! As mentioned there were no keys. I popped one of the door locks off and had a key made for it. Unfortunately this key only works in both doors and ignition. I always assumed that this car would be like every other GM I've owned in where the doors and trunk were keyed alike and the ignition was it's own key. I guessed wrong it seems. What am I going to need to do to pop the trunk? Is the trunk key the same as the glove box key? I've tried pumping a blast of air into the vac line for the trunk but only get a slight hiss coming from the trunk area. It's imperative that I get into that trunk to take stock of whatever parts may be in there. I'd hate to buy up a bunch of stuff only to find out they were in the trunk all along. Advise me please.

Thanks,

Greg

Views: 323

Reply to This

Replies to This Discussion

Minor update: The glove box is keyed the same as the doors and ignition. I would assume that the trunk is as well but the key refuses to budge the lock. I have jiggled and wiggled it six ways from Sunday and no dice. Short of calling in a locksmith (which I loathe to do) I'm out of ideas.

The door and ignition are the same key. the glove box and trunk are the same key. Since you have the power trunk, put vacuum to the line going to the trunk. Hopefully you get lucky with that.

If not, take the glove box lock out.  The lock has no numbers stamped on it, but a lock smith can easily look at it and tell what the code is.   Hold the chrome bezel still, and move the glove box lock assembly back and forth. that should loosen up the bezel. It just unscrews and the lock will fall out.

Or take a 7/16 socket and get it to the 3 bolts that hold the trunk latch in the deck lid.  The deck lid would then lift up.

How do our car locks get so screwed up!! My door and trunk is the same key and the ignition key is different. I've never tried the glove box yet but I am going to now.
If you attach a hand vacuum pump to the trunk power release that might work.

Thanks to all that replied.

I eventually got the trunk to open. It took a lot of patience and jiggling of the key to get it there though. It seems as if the tumbler for the trunk is worn. I'll have to take it to the locksmith and get them to repair it. Unfortunately the vacuum trick didn't work this time but I got it to open eventually. Patience is a virtue.

It seems that at some point someone had all the locks and ignition keyed the same. I'm okay with that but I still prefer the "old school" way of having the ignition and doors keyed differently.

Cheers,

Greg

Greg my door locks didn't work when I first got my car. When I realized what was going on I sprayed wd40 in them and now they work perfectly. I originally thought I had no door keys.

This thread reminds me of the most overlooked piece of literature most of us have ... our owners  manual.  Page 4 is all about the two separate keys provided - octagonal head for ignition and door locks; rounded head for luggage compartment and glove box. Read that owners manual and you will be surprised at the wealth of information. If anyone needs one I have a very good 1964 manual from last parts car for $25 + s/h.

The ignition key can be removed while the car is running ,which is different to me ,from other cars
Helps if you need to get to the trunk key
Do not lock your keys in the trunk ,by accident
That is what a Hide a Key is for
I find a Hide a key to be a very good idea ,when it is needed
I have been using them for about 50 years on all my cars
It can truly rescue you when needed

Enjoy

That just means that the key is worn. The key should not be able to be removed when the switch is turned on.

Russ is correct. I've had a few driver and parts cars where the key would remove when switched on, but that is from a worn key and/or lock.

Still using the original keys ,so a lot of room for wear over 52 years
Interesting to learn ,wear is responsible for the convienence it affords
Thanks guys

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

How much play in 63 timing chain?

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Ben Roberts 5 hours ago. 6 Replies

I will be installing a new chain and gears because I'm in this deep and all the forums here strongly recommend doing so.  It appears the coating is intact and I don't have to worry about that debris…Continue

The Australian Bushfires:.......

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 6 hours ago. 11 Replies

I know we have some Aussies on here and I have to say, Australia, is in a whole world of hurt at the moment, so do ya best to stay safe.Currently, in the southern states, 4 huge fire fronts, look…Continue

1964 sixty special fleetwood piston ring need help

Started by Pablo in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 1 Reply

Good morning, I just got an engine that needs piston rings , it’s a 429 cid , the measure of the piston is 104 14 according with the digital caliper, also the size of cylinder shows 105 01 , the…Continue

Blog Posts

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

AC/heater for 1964 Cadillac coupe de ville

Posted by Matias J. Adrogue on January 7, 2020 at 11:11am 9 Comments

Good morning!  I am Matias Adrogue.  I bought a 1964 Cadillac coupe de ville last year and am real close to the final restoration details!  I call her “Jaws 64”.  Pics will be posted soon.  I need advise regarding a AC/heater.  It came stock in the vehicle but it does not work.  A mechanic gave me a bid of $1700 to replace and repair.  I am ready to install a new system - Vintage Air or Old Air Products from Fort Worth Texas.  I would greatly appreciate your thoughts.  I read the great write…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service