Hey guys.

Im going to be pulling my engine and tranny out soon. Theres some leaks on my engine and tranny. The main reason for this is because i need to paint the engine and engine bay. So i might as well go through everything and replace all gaskets and seals. Im going to be pulling most of the parts off the engine to sandblast and paint. Im pretty new here and was wondering if anyone has a parts list of what i would need. I would want to change front and rear mains seals, valve cover, oil pan seals, etc. If some can help me out with what i will need and maybe what site you guys order off of. That would be appreciated. 

Btw i have 1963 deville series 62. Not sure what transmission it has in it. I have posted pictures of the gear selector since i read on here you can identify tranny from that. I have also posted pictures of the engine so you guys know what im dealing with. LOL. 

Thanks alot guys!

Views: 829

Attachments:

Reply to This

Replies to This Discussion

Tony, you are beating on an old topic like a sick dying horse that I explained in some detail. Basically engine had 3K miles after rebuild, All internals were new, I have a solid tick/tap on right side as of a drive to Charlotte, NC May 2018. I thought it was a dead lifter, took it to the machine shop and let the "guys" come out and give it a listen and they all said dead valve lifter. That was May 2018! Car runs good but has that tick/tap. I bought a full set of quality USA Made Melling Lifters and Pushrods. No sense in trying to find and replace one, when I can replace all lifters and pushrods with more new quality stiff for just over one Ben Franklin note. I will let you guys and gals in Cadillac-Land know if that fixes it when I get to it. Right now I'm in the middle of roofing, electrical, siding, plumbing and all else that goes in with my new house addition. By this time next year I should be freeing up. :-)

Got the heads off. Very minimal ridge at top of cylinders. Walls look pretty good. Ill take some pics when i get home. Does anyone know what the clearance is for main and rod bearings? I was going to plasti guage them. Im not sure if i should pull the pistons and rering them since im already in this far. Its not too costly anyways.

Im going need valve seals for sure. Anyone know which ones i need and are good quality?

Can someone give this gentleman the correct clearances for the rod and crank bearings ?

Try —Rock Auto - for the valve seals 

I use to use PC valve seals in my race engines in the past 

Enjoy 

So i looked at the service manual more in depth and found the specs.

Rod bearings should be replaced if clearance is greater than .0035"

Main bearings should be replaced if more than .0045"

RSS

Photos

  • Add Photos
  • View All

Forum

1963 Convertible - No Backup Lights

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Charles Fares 39 minutes ago. 1 Reply

The backup lights worked on my '63 Series 62 convertible when I bought it in July, but have stopped working. All other lights work fine. There is no power coming to the connectors behind the license…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 8 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

spark plugs

Started by Ron Perry in 1963/64 Cadillac Specific Discussion. Last reply by Ron Perry 23 hours ago. 6 Replies

Gentlemen   I have a 1964 Sedan De Ville with 20 thousand original miles. I am going to replace the spark plugs. What plug would you recommend? I only drive the car a few hundred miles a year and the…Continue

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service