Hey Guys,
I’m having a hard time getting to the motor mounts that  attach to the frame, not the engine. Can someone share how they got them loose. What size is the nut?  3/4’’ ? It looks like the are adjustable, in a slotted hole. Mine are all the way down on the slot making it hard the get a socket on it. A deep well socket is too long and a short socket, the bolt bottoms out before it gets on the nut. I have even tried a swivel extension. At a loss now. Oh by the way the engine is out off the car.

thanks

curt

Views: 54

Reply to This

Replies to This Discussion

I use a wrench and go from the bottom.

The Motor mount attaches to the frame via a 3/4"-20 hex nut, 3/4" split lock washer and a very thick flat washer that is about 1/4" thick and  1 1/2" wide as seen in the picture below. If you have the original flat and lock washer and nut on yours, there should not be a need for a deep socket. If missing washers and maybe using a jam nut you may need something a bit deeper socket but I don't remember ever  having to use one.  

So, with a large nut like this you want to use the larger 1/2" Drive ratchet, extension, U joint, and nut.  Even if you can find a 5/16" Drive 3/4" socket you want to leave it in the tool box.. and if using 5/16" tools that might be a reason your socket will not reach the nut as they are usually shorter than the 1/2" Drive sockets.

With that here is my process from probably the last 50 of 58 parts cars: Raise front or front corner of car a bit & turn steering wheel so front wheel is turned out to give easy access under the frame area where motor mount goes through.  I use a 1/2 Drive ratchet, 1 foot extension bar, U Joint, & 3/4" socket, attached in that order.  I'm sure you know the old trick of wrapping electrical tape around the U joint so it doesn't flop around. 

Again, I never remember having an issue with that large nut, once I figured out the right tools to use.  When I remove an engine I always disconnect the motor mount from the frame via that one large  nut, since after doing it so many times it is almost always about a 5 minute removal per side.

If you are missing the thick washer, or lock washer and even perhaps the nut I do have all the correct, original hardware cad plated as seen below. You an see more pictures and details by Clicking Here.

RSS

Photos

  • Add Photos
  • View All

Forum

KleerView/OptiKleen Bottle Location

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 8 hours ago. 3 Replies

I just received a repop KleerView bottle and label for my 64 Fleetwood this morning. Wondering where the best location for this bottle would be? Or rather, where was it most commonly installed?I…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 22 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

1964 A/C Delco Parts book for Deville

Started by Mark Bartlett in General Discussion. Last reply by Jason Edge yesterday. 1 Reply

Is there a place to go to buy or look at original parts book ThanksssContinue

differential seal

Started by Al zink in 1963/64 Cadillac Specific Discussion. Last reply by Al zink on Monday. 2 Replies

Can anyone provide me with a good source for a differential seal for my 63 cadillacThanksContinue

Blog Posts

Lower Front End Ball Joints

Posted by Logan Robb on May 11, 2023 at 9:04am 7 Comments

Good Morning all! 



I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…

Continue

1964 power steering sector rebuild

Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments

 I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response,   has anyone done this? and how do you like it? thank you

1964 Daville dashboard clock

Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments

Hallo,

Can somebody help me finding a dashboard clock  for my 1964 Cadillac DeVille Convertible?

Thank you in advance,

Willem Bol

The Netherlands

Does anyone know where I can get the bushings for AC compressor mount on the 429?

Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments

I've looked at the usual rubber sources but couldn't find any. 

Videos

  • Add Videos
  • View All

© 2023   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service