spring cleaning time, replaced the fuel filter after a long spell, and now a leak from the top of the tank!
related?
easily a drop a second or more in volume.
I’m assuming its a corrupt hose, is it easy to get at with the rear on jack stands?
Thanks!
Tags:
You have a gas tank venting hose in front of the gas tank- just above the rear axel
Do be sure that piece of metal S shaped tubing and hose are in good condition
Not sure what leaking from the top means but leaking gas can get expensive real quick with our prices rising every few days in Florida USA
From 2.19 a gallon to 2.59 at present in about a week or so
Enjoy
From reading other posts I ‘m hoping its the vent hose.
leaks down the front of the tank from the top.
Thanks!
The gas tank overflow tube may not be in its correct position
A gas smell when on an incline is an indication That tube is not in its correct position
The hose coupling there can be worn cracked and leaking
Remove that hose to inspect it as i could not see the rubber hose damage until i did that in my case
The hose looked good until examining it in front of my nose with it off the car In my case so just a heads up on that
Really liked doing that necessary repair to eliminate my sometimes gas smell in my own garage
Felt good to eliminate that problem
All gas related rubber hosing SB ethanol compatble these days to prevent rubber hose detereration from the gas We are using
Enjoy
Replace all three fuel line hoses. They are rotten if never changed before and or the ethanol in the fuel has done them in. Vent, return and fuel line. As Tony has stated.
All the fuel lines go to the top of the gas tank on the passenger side of the tank
Removing the rear passenger tire and rim will have you looking at the fuel lines there
Good chance one or more of those rubber hoses are split and damaged from wear and age
SB an easy fix just replacing hoses using hose compatible with todays Ethanol fuel and some hose clamps
An easy fix to loosing expensive gas and a gas fuel smell
Enjoy
Started by Kai Dröse in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 7 Replies 0 Likes
Hi from germany,i know here is a many content about wiring plans and so on.but i need the correct wiring plan for my new dream car ;) the passenger window does not work…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 on Tuesday. 10 Replies 0 Likes
I've posted a few times about the strange issue I have with the trans on my 64 Fleetwood. When it gets warm and up to temp, I loose 3rd gear, but I never loose reverse. According to multiple sources,…Continue
Started by Henrik Sonne in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 on Tuesday. 14 Replies 0 Likes
First I will start by saying, I am a newbie. Recently purchased a ´56 HT, which has a 390" from a ´63 in it. I have decided to put a new Holley on it, but not 100% sure which one would be the best…Continue
Started by Sammy in 1963/64 Cadillac Specific Discussion on Tuesday. 0 Replies 0 Likes
Time again to change my shocks. No matter if Gabriel, ACDelco whatever - don't last longer than 3 or 4 years.Problem is the rubber parts thats gliding out of the bottom.But now I have another…Continue
Posted by ANGELO MARTINEZ on July 23, 2023 at 10:44pm 3 Comments 0 Likes
Hope someone can help me to find the harmonic balancer bolt for my 1964 Cadilac Deville 429 engine
in advance, thank you for your help.
Posted by Matt Vander Hooven on July 23, 2023 at 7:36pm 2 Comments 0 Likes
Is there still a member in the Detroit area that refurbishes clocks?
Matt VH
Posted by Patrick Westphal on July 7, 2023 at 10:00am 3 Comments 0 Likes
I found a diagram that illustrates the main factor in determining a spark plug heat range that I was trying to describe to you during the chapter get together.
Here it is:
The main factor is the length of the ceramic insulator from the middle of the spark plug to the tip (where the spark happens)
The insulator…
ContinuePosted by Logan Robb on May 11, 2023 at 9:04am 7 Comments 0 Likes
Good Morning all!
I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…
Continue
© 2023 Created by Jason Edge.
Powered by