I'm in the middle of replacing my rear main seal and need to rotate the driveline so I can install 2 nuts on the flywheel. Oil pan is off. What's the best way to go about this?
63 390

Views: 164

Reply to This

Replies to This Discussion

Pull the plugs, and grab the crank pulley.  Or put a bolt in the end of the crank and turn with a ratchet.

what size bolt? where?

thanks

The bolt goes into the end of the crank shaft, up by the radiator. I dont remember off hand what size it is.

I usually use a flywheel turning tool like this one...http://www.amazon.com/Powerbuilt-648455-Flywheel-Turning-Tool/dp/B0...

Or a strap wrench on the crankshaft pulley.
Pull the plugs out ,so the engine will spin more freely and easily( go to Neutral)
One of the Front bumper bolts is the same size as the crank pully bolt ,i am sure
I cannot give you the size ,but very sure ,Jason knows the size
If you install the bolt in the crank ,use a ratchet,with a --hydraulic jack handle -over that ,for all the leverage you could need ( just a 1/2 inch ratchet ,may work with the plugs out )
Real good to repair that seal and leak
Do fill us in on the tricks or special things you do to get this job done right
Were did you aquire all the parts and gaskets
Thanks

I used a Proform 66782 crankshaft rotater tool when I rotated mine.

http://www.ebay.com/itm/Proform-Crankshaft-Turning-Tool-Crank-Rotat...

Pulley has to be off, mark location of pulley shim/washer holes with pulley since they seem to line up to holes one way when you put the pulley back on, use the pulley bolts to mount tool to damper.  I used  a ratchet at the end of the tool with a pipe for leverage.

Unless your engine is seized or has not been cranked in some time you should be able to remove spark plugs and grab the alternator belt and turn the engine.  A helper on the other side can assist.

RSS

Photos

  • Add Photos
  • View All

Forum

Power Brake Booster

Started by Stephen A. Pechenik in General Discussion. Last reply by Stephen A. Pechenik 55 minutes ago. 5 Replies

Hello Co-Members,I recently purchased a  low mileage1963 Sedan Deville Park Avenue.  It is extremely solid and runs well.  Neverthelss, it has minor problems that need to be addressed before I can…Continue

Jeremy LeBlanc

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 9 hours ago. 4 Replies

Jeremy I am very interested in learning all you can tell me and the community about your engine swap to the 2019 LS2 L96 Silverado engine and 6L90 trans you installed in your 63Any details you could…Continue

Tags: 63, to, swap, engine, Silverado

Dan McNarry

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 10 hours ago. 5 Replies

Dan Have you come up with any solution for the front bushings of the rear trailing arms of our year cars ?I thought you had suggested you were thinking about what you might do about that Stay Safe Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 23 hours ago. 178 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

1964 Cadillac fleetwood sixty special vanilla top windshield needed

Posted by Pablo on April 5, 2020 at 10:00pm 3 Comments

If anybody has or know where Can I get a windshield glass for my 1964 Cadillac fleetwood sixty special with vinyl  top? I will appreciate any info.

Thank you very much

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service