I need some help/advice guys and gals! The short story: I purchased my '64 deVille in 2011 from dealer in Utah. Drove it home with a couple of minor issues to Virginia. Started working on headlight switch, undr dash pad vacuum tubing, etc. Due to work schedule, etc, I let the car sit until this year - I know, I've beat myself up enough.
Going through anything that may give me trouble (hoses, cap/rotor/points/condenser, belts ...) on the 2,200 mi trip home to Montana. I just replaced my pts/condenser, found my vacuum advance is bad (ordered one), and was starting to swap the plug wires onto the new cap when placement of #1 didn't look right. Firing order is 18726543, and the workshop manual's picture of the cap with wire numbers marked shows #1 between screw and window, and #8 next, at the corner of the window, CW. The way it was wired is #1 is CCW two positions. The firing order is correct and the car ran well back then.
Am I nuts or did the rebuild mechanics get the distributor in wrong and made up for it by clocking the wires to get it to run? The shop manual that came with the car is marked with highlights, stars and question marks, leading me to think this may have been their first rebuild.
I'm new at posting, will try to add photos. Thanks in advance for any help,
Linda
Tags:
Hi Linda,
Your comments are the best. I would pop in the new check valve and the new 11/32 hose for the booster - can't hurt. You're right; the parts stores don't carry that special hose - thought I was from Mars! Now that your advance is in, you should be good to go. Thanks for the compliment on my Caddy. Safe trip back to Big Sky Country. Take your time.
Dennis
Thanks Dennis, I'll install the new check valve and grommet (if it fits), the hose is new - I meant to say 11/32", so good to go there. OPGI can get the Bendix booster rebuild kit, but hope mine is good enough to get me home.
Thanks for the advice and conversation, not many people I know like to talk old cars. Best wishes,
Linda
OK Linda,
Good trip and we'll talk soon!! You are very welcome.
Dennis
Started by Jason Edge in Trivia 5 hours ago. 0 Replies 0 Likes
What % of 1963 and 1964 Cadillacs came with the optional "soft ray" tented glass? 1963 & 1964 were very close, so if you get one you will get the other. Need to get it within 3%. So, who will…Continue
Started by Jason Edge in Trivia. Last reply by Jason Edge 5 hours ago. 3 Replies 0 Likes
It has been way too long since we posted any trivia (and gave out a cigar), so here is one I thought I might have posted but do not see it: What % of 1963 Cadillacs came with the optional "Controlled…Continue
Started by Jason Edge in For Sale. Last reply by Jason Edge on Friday. 2 Replies 0 Likes
I had an older couple contact me indicating they are selling their 1963 Coupe de Ville they have had for 40 years and they are located Moyock, NC, which is in the very north east part of North…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Thursday. 15 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by